Panasonic AG-HPX500 Operating Instructions Manual page 70

Remaining battery charge
16
As the remaining battery charge drops, the
display changes as follows:
When the battery has completely discharged,
( ) blinks.
(When the AC adapter is being used, a display
other than may appear: this is not a sign of
malfunctioning.)
• 13.5V: Battery voltage indication
Indicates the current voltage for analog
batteries.
• XX%: 10% to 99%
Indicates the remaining battery level in % for
digital batteries.
This value is not indicated on the meter.
• MAX: Indicates that a digital battery is fully
charged.
• EMP: Indicates that a digital battery has a
remaining charge of less than 10%.
• Battery type indication
Holding down the DISP/MODE CHK button
will show the value currently set for battery
remaining level indication.
"AC ADPT" is shown when the AC adapter is
used.
Text memo and shot mark indicator
17
• This indicator lights when text memos are
inserted during recording or playback by
pressing the USER button to which the TEXT
MEMO function has been assigned.
• "MARK ON" appears when shot marks are
inserted during recording by pressing the USER
button to which the SHOT MARK function has
been assigned.
A second press will delete the shot mark and
MARK OFF appears.
• "INVALID" appears when a text memo could not
be entered or a shot mark could not be recorded
or deleted.
Recommended ND filter
18
The recommended ND filter under the current
shooting conditions is displayed here.
ND filter display
19
• ND filter selected is displayed.
• An "ND –" indication means that the ND FILTER
switch is incorrectly set (a position other than
ND1 to ND4). Check ND FILTER switch position.
Gain display
20
Displays the gain value of the image amplifier
configured.
WHITE BAL switch position indication
21
Indicates the switch position currently selected.
Also indicates white balance operation when
AWB is set to "preset".
Center marker display
22
Markers are displayed when the MARKER item in
the setting menu DISPLAY SETUP screen is set
to ON.
23
Scene file name display
Indicates name of SCENE FILE (F1 to F6).
70
Viewfinder Screen Status Displays
24
→ → → →
25
26
Media remaining memory display
• Setting the setting menu P2 CARD REMAIN
(DISPLAY SETUP) to ONE-CARD displays the
remaining time on the P2 card that is currently
being recorded and the number of the slot it
resides in. Setting P2 CARD REMAIN to TOTAL
displays the remaining time on all four cards.
• In a mode check, "ONE-CARD" and "TOTAL"
are alternately displayed.
• There is no display while the remaining memory
is being calculated. "LOOP" is displayed during
Loop recording (LOOP REC).
• In a mode check during loop recording, the
minimum guaranteed available recording time is
displayed.
• Indicates remaining time in 1-minute increments
from 0 to 999 minutes.
• The display blinks when 2 minutes or less time
is left.
Operational state display
• REC: Recording
• PAUSE: Recording pause
• : Play pause
• ( ): Play (reverse play)
• ( ): Fast-forward/Fast-forward play
(Rewind/Fast-backward play)
• ( ): Slow play (Reverse slow play)
• CHK: Rec check
( ): Frame-by-frame (Reverse Frame-by-
•
frame)
• × / × (× / × ): Variable-speed search
(Reverse variable-speed
search)
• CLIP (CLIP ): Clip forward (Clip reverse)
Cue up of single clips
Not displayed when the LCD is off in CAMERA
mode. (But displayed when pre-recording, interval
recording or one-shot recording is set.)
Media information display
The card slot where the P2 card was inserted and
the basic information of the media are displayed
here.
• 1 lights: P2 card on which data can be
recorded.
• 1 lights green: P2 card on which data is to
be recorded.
• 1 Flashes: Card recognition underway, or
a card other than that on which
data is to be recorded in special
recording mode
• — : No card inserted.
• P : Write-protected
• F : Full memory
• X : Cannot recognize
• E : a P2 card in an invalid format
(Returns to normal if formatted.)