Kyocera KM-C2630D Operation Manual page 127

2
Select the desired magnification ratio.
If you want to have the copy magnification ratio selected
automatically, press the "AMS" key.
If you want to manually set the magnification ratio, press
the "# keys" ["#-Keys"] key and then enter the desired ratio
with the keypad, or press the "+" key or the "-" key to
change the displayed magnification ratio to the desired
setting in 1% increments.
You can also select the magnification ratio by pressing the
preset zoom ratio keys at the right that corresponds to the
desired ratio.
Inch specifications
Ready to Job build.(Full-color)
Place originals then press Start key.
Reduce/Enlarge
( 25 400)
100 %
Standard
Zoom
XY Zoom
# keys
Metric specifications
Ready to Job build.(Full Col.)
Set original. Press Start key.
Reduce/Enlarge
( 25 400)
100 %
Standard
Zoom
XY Zoom
#-Keys
Metric specifications (Asia Pacific)
Ready to copy.(Full Col.)
Set original. Press Start key.
Reduce/Enlarge
( 25 400)
100
Standard
Zoom
XY Zoom
#-Keys
3
Press the "Close" key.
The touch panel will return to the screen in step 1.
Back
154% 77%
AMS
5 / x8 / 8 / x14 11x17 8
1 1 1
2 2 2
100% 129% 64%
8 / x11 11x17 11x17 8
1
2
400% 121% 50%
8 / x14 11x17 11x17 5
1
2
200% 78% 25%
5 / x8 / 11x17 8 / x14 8 / x11
1 1 1 1
2 2
2 2
Back
141% 75%
A 4 A 3
AMS
A 5 A 4 11x15
100% 127% 70%
Folio A 3
400% 106% 50%
11x15 A 3
200% 90% 25%
A 5 A 3 Folio A 4
Back
141% A 4 A 3 81%
%
AMS
B 5 B 4
A 4 B 4
100% 122% 70%
A 5 B 5
400% 115% B 4 A 3 50%
B 5 A 4
200% 86% A 3 B 4 25%
A 5 A 3 A 4 B 5
Section 6 OTHER CONVENIENT FUNCTIONS
Specifying the direction that the originals were
set
This procedure specifies the direction of the set originals.
1
With the content of the "Basic" tab displayed, press the
"Orig.set direction" key.
The "Orig.set direction" screen will be displayed.
Inch specifications
Ready to Job build.(Full-color)
Place originals then press Start key.
Job Build - Step 1
set
Select
paper
Offset
Close
Finished
Basic
/ x14
1
2
/ x11
1
2
Metric specifications
/ x8 /
1 1
2 2
Ready to Job build.(Full Col.)
Set original. Press Start key.
Job Build - Step 1
set
Select
paper
Group
Close
Finished
Basic
A 4
A 3 A 4
A 4 A 5
2
Press the "Rear" ["Back Edge"] key or the "Left top corner"
key, as appropriate, according to the direction of the
originals.
Inch specifications
Set
Ready to Job build.(Full-color)
Place originals then press Start key.
Close
Orig. set direction
B 4 A 4
B 5 A 5
A 3 A 4
B 4 B 5
Metric specifications
Ready to Job build.(Full Col.)
Set original. Press Start key.
Orig. set direction
IMPORTANT!
If the designation for the direction that the originals are
set is not correct, copying may be accomplished
incorrectly.
3
Press the "Close" key.
The touch panel will return to the screen in step 1.
1 sided 1 sided copy
11x8 /
1
2
Original 1 sided/
type 2 sided
1 sided copy-Left
AMS Back Edge
Finished page #: 0
Reduce Orig. set
/Enlarge direction
Quality Edit
1-sided 1-sided Copy
Original 1-sided/
type 2-sided
1-sided Copy-Left
AMS Back Edge
Finished page #: 0
Reduce/ Orig. set
Enlarge direction
Quality Edit
"Check direction original" can be shown
at right side of display.
Follow the steps. If setting mode is
wrong, incorrect copy will result.
"Check direction original" can be shown
at right side of display.
Follow the steps. If setting mode is
wrong, incorrect copy will result.
set
End
Insert
page
set
End
Insert
blank page
set
Back Close
Check direction
Check direction of
original top side.
Left top
Rear
corner
set
Back Close
Check direction
Check direction of
original.
Left top
Back Edge
corner
6-77