Denon AVR-1612 Owner's Manual page 95

GAudioH
Symptom
Audio is not output. • Check the connections for all devices.
• Check the speaker connections and configurations.
• Check whether the audio device power is turned on.
• Adjust the master volume.
• Cancel the mute mode.
• Select a suitable input source.
• Select a suitable input mode.
• Disconnect the headphones. No sound is output from the speakers
or the PRE OUT connectors when headphones are connected.
No sound is • Check if the surround speakers are connected to the SURROUND
produced from terminals.
surround speaker.
No sound is • Check if "Pre Assign" is set appropriately in order to output audio
produced from from the surround back speakers.
surround back • Set "Speaker Config." – "S.Back" on the menu to something
speaker. other than "None".
• Set "Surr.Parameter" – "S.Back" on the menu to something
other than "OFF".
• Set the surround mode to something other than "STEREO" and
"VIRTUAL".
No sound is
• Set "Surr.Parameter" – "PLgz Height" on the menu to "ON".
produced from front
• Check if "Pre Assign" is set appropriately in order to output audio
height speaker.
from the front height speakers.
• Set "Speaker Config." – "F.Height" on the menu to something
other than "None".
No sound is • Check the subwoofer connections.
produced from
subwoofer.
• Turn on the subwoofer's power.
• Set "Speaker Config." – "Subwoofer" on the menu to "Yes".
• If "Front" and "Center" for "Speaker Config." are set to "Large",
and "Subwoofer Mode" is set to "LFE", no sound may be output
from the subwoofers, depending on the input signal or selected
surround mode.
DTS sound is not • Set "Decode Mode" on the menu to "Auto" or "DTS".
output.
Dolby TrueHD, DTS- • Make HDMI connections.
HD, Dolby Digital
Plus audio is not
output.
Cause/Solution
6, 7, 8, 9, 10
Symptom
Page
• Check that "Speaker Config." – "Center" or "Surround" is set
Dolby PLg mode or
to other than "None". If the speaker system is 2.0/2.1ch, this
C 3, DTS NEO:6 mode
surround mode cannot be selected.
cannot be selected.
• When headphones are used, Dolby PLg or DTS NEO:6 cannot be
C 6,
selected.
59, 60
Audyssey MultEQ ® ,
–
• Switch the surround mode to other than "DIRECT".
• When headphones are used, MultEQ ® , Dynamic EQ ® and
19
Audyssey Dynamic
EQ ® and Audyssey Dynamic Volume ® cannot be selected.
19
Dynamic Volume ®
18
69
cannot be selected.
78
Dynamic EQ ® and • Make Audyssey ® Auto Setup.
Dynamic Volume ®
–
cannot be selected.
RESTORER cannot • Check that an analog signal or PCM signal (fs=44.1/48 kHz) is
be selected. input. For playback of multichannel signals such as Dolby Digital
59
or DTS surround, RESTORER cannot be used.
• Switch the surround mode to other than "DIRECT".
59
GRadioH
53
Symptom
Reception fails, or • Change the antenna orientation or position.
29
there is a lot of noise • Separate the AM loop antenna from the unit.
or distortion. • Use an FM outdoor antenna.
53
• Separate the antenna from other connection cables.
59
GControl dock for iPodH
60
Symptom
iPod cannot be • Check the iPod connections.
C 6,
played. • Insert the AC adaptor of the iPod control dock into the power
36, 37 outlet.
• Switch the input source to "DOCK".
–
59
59, 60
69
6
92
Cause/Solution
Cause/Solution
Cause/Solution
Page
59
–
32
–
11, 40
56
32
Page
10
10
10
10
Page
9
–
18