Page 1
Ver. 1 SERVICE MANUAL MODEL E1K E1C AVR-1612 AVR-1622 AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
VOLUME UNIT ................81 POWER UNIT .................81 JIG FOR SERVICING ..............35 HEADPHONE UNIT ..............81 WHEN THE MICROPROCESSOR IS iPod/USB UNIT (AVR-1612 ONLY) .........81 REPLACED WITH A NEW ONE ..........37 PORTABLE UNIT (AVR-1312 ONLY) ........81 PROCEDURE FOR UPGRADING REGULATOR UNIT (AVR-1312 ONLY) ........81 THE VERSION OF THE FIRMWARE ........37...
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
8 iPod system 9 Service Jig When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from Denon Official Service Distributor in your region if necessary. 8U-110084S EXTENSION UNIT KIT 1 Set (Refer to 35 page.)
DISASSEMBLY • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". •...
Page 8
About the photos used for "descriptions of the DISASSEMBLY" section • The shooting direction of each photograph used herein is indicated on the left side of the respective photograph as "Shooting direction: ***". • Refer to the diagram below about the shooting direction of each photograph. •...
1. HDMI UNIT ASSY Proceeding : TOP CABINET HDMI UNIT ASSY → Disconnect the connector board. CONNECTOR PCB Shooting direction: C Remove the screws. Shooting of photograph: A Remove the screws and board. Cut the wire clamp band, then disconnect the connector wire and the FFC cables. FFC Cable CN151 CN252...
2. FRONT PANEL ASSY Proceeding : TOP CABINET HDMI UNIT ASSY FRONT PANEL ASSY → → Remove the screws. View from the bottom Cut the wire clamp band, then remove the screws. Disconnect the connector wires. CN407 CN603 CN604 Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.
4. RADIATOR ASSY Proceeding : TOP CABINET HDMI UNIT ASSY INPUT PCB ASSY → → RADIATOR ASSY → Remove the screws, then disconnect the connector wires. CN603 RADIATOR ASS'Y CN703 Remove the screws, then remove the REAR PANEL. Shooting of photograph: A...
5. REGULATOR PCB Proceeding : TOP CABINET REGULATOR PCB → Please refer to "EXPLODED VIEW" for the disassembly method of REGULATOR PCB. 6. SMPS PCB Proceeding : TOP CABINET SMPS PCB → Please refer to "EXPLODED VIEW" for the disassembly method of SMPS PCB. 7.
2 STATUS paths. (Troubleshooting) The signal paths of the set can be easily confirmed after repair. When using multiple DENON AV receivers in the same room, make Remote ID Setup mode iPod system 2 STATUS this setting so that only the desired AV receiver operates.(Refer to 19...
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When the set is started up in this mode, the version information is displayed. Starting up: Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "DIMMER" buttons. Now, press the "STATUS"...
Page 16
1.3. Error display See the following table for each "Error information" display and its explanation (status). Display order is q , w , e , r , t . Condition Status FL Display Trouble shooting • Please check the Compared with the destination setting destination-resistors (R2031/R2032, on the board.
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifications Error mode (Displaying the protection history): When the set is started up in this mode, the error information is displayed. Starting up: • Common in all the models Press the "ON/STANDBY" button to turn on the power while pressing the "STATUS" and "SLEEP" buttons. The error (protection history display) mode is set.
Page 18
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. Start up the set in error (protection display) mode and display the error, then press and hold down the "iPod 1 " button for 3 seconds. P R T : D C Press the "iPod 1 "...
3. Remote ID Setup mode 3.1. Specifications When using multiple DENON AV receivers in the same room, make this setting so that only the desired AV receiver operates. 2.2. Setting the AV receivers Starting up: Press and hold both "STATUS" and "iPod system 2 " buttons for over 3 second with the power turned on.
4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 4.1. Starting diagnostic mode Press the "iPod system 2 "...
Page 22
4.5. Audio system confirmation items fig.XX : Refer to the block diagram of the fig.XXth. Output sequence of remote control codes Confirmation item Setting and display Details of how to operate remote controller Contents of confirmation Remarks b It is useful to form a macro program. Analog (signal) Path Input Mode : Fixed ANALOG 1.Press [ZONE SELECT], Select "MAIN"...
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from DENON Official Service. Distributor in your region if necessary. NOTE: The incorrect connection with in the JIG (EXTENSION UNIT KIT) may cause damage.
Page 36
(3) Detach PCB DIGITAL is detached from the chassis, and turn it over. Please put an insulation sheet that is larger than PCB DIGITAL under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. PCB DIGITAL Ground lead Insulation sheet...
WHEN THE MICROPROCESSOR IS REPLACED WITH A NEW ONE When the U-PRO (Microprocessor) or the Flash ROM is replaced, confirm the following. After PWB Name Ref. No. Description Remark replaced DIGITAL IC201 R5F56108VNFP SOFTWARE: Main DIGITAL IC406 MX29LV160DBTI-70G SOFTWARE: DSP ROM DIGITAL IC403 EPM3032A-TC44...
Page 38
1.3. Turn on the AV receiver Operate the following. Turn on the AV receiver. (1) Connect the power cable to the AC outlet while simultaneously pushing the "NET/USB" button and the "INTERNET RADIO" button of the front panel. (2) Confirm the power indicator is green and "WRITTING" is displayed in the front panel. 1.4.
Page 39
1.6. Download the firmware (1) Click the "Load" button. (2) Download the firmware from the specified download source to PC. XXX-XXXX XXX-XXXX_WWWXXXXYYYY-ZZZZ.bin XXX-XXXX_WWWXXXXYYYY-ZZZZ.bin 1.7. Complete the firmware updating (1) Click the "Update" button. XXXXXXXX XXXXXXX (2) When writing of the firmware is completed, the power of AV receiver turns on automatically and you can see the "Update completed"...
Page 40
(3) If you can’t complete the firmware update, please retry the firmware update from "1.3. Turn on the AV receiver". 1.8. Notice: Please keep the following notice for firmware update. (a) Keep the PC environment (b) Avoid the communication cable from the electrical noise source. (e.g.
ADJUSTMENT Audio Section Adjusting Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan and humidity should be moderate, and place the set at normal usage environment. Temperature should be at 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, When the power turned on, does the ON/STANDBY does the ON/STANDBY indicator on the front panel indicator on the front panel flashing green? flashing red? Is the fuse blown? Refer to 1.2.Fuse is blown.
2. Analog video MONITOR OUT (CVBS) output NG Input CVBS Input S Function : SAT Function : DOCK To A To B...
Page 48
Input CVBS Is the power supply voltage correctly output? REGULATOR B'D flaw. V+5V : C4096 : + side V-5V : C4099 : - side Check on set value of each IC. Is they the following voltage values? DIGITAL B'D flaw. SIDE CONNECTOR B'D CN254-8pin : H(3.3V) CN254-7pin : L(0V)
Page 49
Input Is the power supply voltage correctly output? REGULATOR B'D flaw. V+5V : C4096 : + side V-5V : C4099 : - side Check on set value of each IC. Is they the following voltage values? SIDE CONNECTOR B'D DIGITAL B'D flaw. CN254-8pin : H(3.3V) CN254-7pin : H(3.3V) CN254-6pin : L(0V)
Page 50
SIDE CNNECTOR test point (COMPONENT SIDE) Detail A CN254 5pin CN254 7pin CN254 8pin CN254 4pin CN254 6pin INPUT test point (COMPONENT SIDE) Detail B IC406 6pin IC406 4pin IC401 9pin IC401 1pin IC401 5pin C4096+ C4099-...
(6) Is the BD/DVD player's HDMI output setting correct? the BD/DVD player's operating instructions. (7) When you use a DENON BD/DVD player's, is the fluorescent display tube's "HDMI" indicator lit? If you use a non-DENON BD/ DVD player's, proceed to "YES".
Page 52
(JK101/JK102/JK103/ display's "HDMI" indicator lit? JK103/JK104 : TP[+5V]) for the input on the side JK104) to the IC101 is If using a non-DENON BD/ on which the BD/DVD player is connected. defective. DVD player, proceed to "NO". Is communication waveform confirmed in...
Page 53
Check operation of each device. (AMP source : BD / Video input of player : 480P / Connect the TV.) Check operation of IC101(ADV7623) (19) Check power supply. Are 1.8V or 3.3V supplied to IC101(each power supply pin)? The power supply circuitry is defective. Refer to [Detail C] of the substrate for test point.
Page 54
3.2. HDMI test point and waveforms (COMPONENT SIDE) Detail A Detail B TMDS D2- TMDS D2- TMDS D2+ TMDS D2+ DDC CLK DDC DATA TMDS D1+ TMDS D1+ DDC DATA TMDS D1- TMDS D0- TMDS CK- TMDS D1- TMDS D0- TMDS CK+ DDC CLK TMDS D0+...
Page 55
DDC_CLK/DDC_DATA/TMDS : Check items (16)/(18) 0.9V DDC_CLK 2.48V TMDS Waveform DDC_DATA Timing waveform illustration from the start of +3V3H to when reset is released : Check items (21) +3V3H 330ms RESET Controlled waveform(I2C), when power is turned on : Check items (22) HSCL HSDA POWER ON...
4. AUDIO 4.1. AUDIO CHECK Audio output NG. Refer to "Audio Check PASS" (63 page). CHECK1 INPUT SURROND MODE SOURCE Check ANALOG audio BLOCK. Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check Digital audio BLOCK. Legacy Audio output OK? COAX or OPT...
Page 57
4.2. Power AMP (MAIN UNIT) No sound is output. The protector operates. Is the power transistor open or short- circuited? Replace the power transistor. 2SB1560/2SD2390 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
Page 58
4.3. Analog audio No sound is output Is the voltage of ±12V supplied to The power supply of ±12V is repaired. INPUT B'D CN406? Is the audio signal transmitted to The power amplifier is repaired. INPUT B'D CN408? Connect the connectors properly. Is the serial data for electronic volume Is the connector correctly connected transmitted to INPUT B'D CN401?
Is the USB device compatible with the set? and iPod (Remove some models) are supported. Checking the set (AVR-1612) Is the wire properly connected between CN341 on the DIGITAL board Connect the wire properly. and BN610 on the USB board.
6. SMPS DC 5V is not output. Is there damage in IC901 Replace the IC901(TOP258MG) and (TOP258MG)? D9001/D9002/D9003/D9004. Is there the damage in D9001/D9002/ Is the fuse (F9001) blown? Replace the damaged parts. D9003/D9004? Does the jumper wire(D9012) connected to the PWB have Repair the jumper wire.
Page 61
Operation waveform for each part Primary drain (Caution: High voltage, electric shock) After primary side rectification (Caution: High voltage, electric shock) After secondary rectifications C9002 0.01uF 250V J9002 D9001 1N4007 JUMPER 2.2M OPEN SMPS B'D D9002 1N4007 R9033 D9003 1N4007 D9012 LF901 SRL3060P...
LEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15218FP ANALOG H/POUT SPEAKER + LINE IN GAIN ADJ. + AK4358VQ MIC IN + AK5358B + + − − ZONE2 SEL. NOT USE REC INH. NOT USE AZ4580 MAX.OUTPUT 7.78Vrms +30dB R2A15218 MAX.OUTPUT 3.8Vrms SPK OUT DIFF.OUT 4.27Vrms/8Ω...
Page 67
LEVEL DIAGRAM CENTER ch R2A15218FP SPEAKER + GAIN ADJ. AK4358VQ + + − − AZ4580 MAX.OUTPUT 7.78Vrms +30dB SPK OUT R2A15218 MAX.OUTPUT 3.8Vrms 4.27Vrms/8Ω DIFF.OUT 0dBFS=5Vpp AK4358VQ =1.77Vrms FULL SCALE LEVEL=2.0Vrms +20dB +20dB 0dBFS POWERAMP GAIN +29dB +10dB +10dB -10dBFS +1.07dB -2.5dB 200mV...
Page 68
LEVEL DIAGRAM SUBWOOFER ch R2A15218FP MUTE PRE OUT GAIN ADJ. AK4358VQ + + − − AZ4580 MAX.OUTPUT 7.78Vrms +30dB PRE OUT FULL SCALE LEVEL=4.0Vrms R2A15218 MAX.OUTPUT 3.8Vrms AK4358VQ +20dB +20dB 0dBFS=1.77Vrms +10dB +10dB PRE OUT PRE OUT 300mVrms 200mVrms 200mV 0dB -30dBFS PRE OUT...
1P WIRE D6015 WIRE OPEN HEADPHONE UNIT CLZ9Z014Z D6016 OPEN C6038 OPEN CJJ9X006Z CJJ2E020Z iPod/USB UNIT (AVR-1612 ONLY) JK601 JK605 CHASSIS AVR1312 ONLY iPod/USB UNIT (AVR-1612 INLY) REGULATOR POWER HEADPHONE PORTABLE UNIT (AVR-1312 ONLY) PORTABLE UNIT (AVR-1312 ONLY) iPOD/USB AVR1612 ONLY...
REGULATOR PART D9310 OPEN CVIKIA7805BPI IC935 J301 OPEN D9315 OPEN HVINJM7812FA F9302 IC931 D9302 1N4007 T 1.25A L 250V D9303 1N4007 COMMON D9319 OPEN 1.DA+5V D9320 OPEN 2.RET_GND(DA) CN932 1.AC_S2 1N4007 3.+12V D9304 2.RET_GND 4.RET_GND F9301 1N4007 D9305 3.AC_S2 5.-12V T 1.25A L 250V 4.NC 6.RLY_GND...
CONNECTOR PART FROM DIGITAL B'D FROM DIGITAL B'D FROM DIGITAL B'D PAGE 4 (2A) PAGE 8 (8C) PAGE 4 (5A) CN258 CN254 CN256 CN257 CN259 CN255 PAGE 10 (8C) PAGE 9 (8C) PAGE 9 (8B) TO INPUT B'D TO INPUT B'D TO INPUT B'D ANALOG AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (15/16)
EXPLODED VIEW E3,E1C model E2,EA,E1C model P18 x4 E2,EA model E2,EA model E3,E1C model WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model E1C : China model(AVR-1612) EA : Australia model 1622E1C : China model(AVR-1622) BK : Black model SP : Premium Silver model Ref.
Page 90
Ref. No. Part No. Part Name Remarks Q'ty SMPS BRACKET CMD1A790 943401100020D TOP CABINET(EMC) CKC2A155ZK117 943401100030D TOP CABINET(EMC) CKC2A155ZD11 HEAT SINK CMY1A371 PCB BRACKET CMD1A417 BRACKET , MULTI AV8003 CMD1A665 BRACKET , PCB CMD1A789 PANEL , REAR E2,EA CKF3A447Z PANEL , REAR CKF1A447Z PANEL , REAR CKF2A447Z...
The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model E1C : China model(AVR-1612) EA : Australia model 1622E1C : China model(AVR-1622) BK : Black model SP : Premium Silver model Ref.
The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model E1C : China model(AVR-1612) EA : Australia model 1622E1C : China model(AVR-1622) BK : Black model...
Page 95
Ref. No. Part No. Part Name Remarks Q'ty C6063-6065 CHIP CAP 0.1UF 50V K CCUS1H104KC C6067 CHIP CAP 0.1UF 50V K CCUS1H104KC C6069,6070 CHIP CAP 330PF 50V J CCUS1H331JA C6071 943134010530S ELECT CAP 1UF 50V C CCEA1HH1R0T C6072-6075 00D9430175108 ELECT CAP 10UF 50V CCEA1HH100T C6089 943134010530S ELECT CAP 1UF 50V C...
DIGITAL PCB UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP IC101 943236012460S IC HDMITransceiver(LQFP-144P) CVIADV7623BSTZ IC102 943248100080S I.C, FLASH MEMORY(AVR1612_E2_OSD) E2,EA CVIANAM1568AV IC102 943248100060S I.C, FLASH MEMORY(AVR1612_E3_OSD) CVIANAM1569AV IC102 943248100090S I.C, FLASH MEMORY(AVR1612_E1C_OSD) CVIANAM1605AV IC151 IC EX3AV CVIEX3AV IC153 IC EX3AV...
MAIN PCB UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP Q7101,7102 00D2710301903 TR KTA1268BLATP CVTKTA1268BLATPA Q7103 00MHT800931A0 TR KTC3200GR HVTKTC3200GRT Q7104 90M-HT800120R TR KTC3114A HVTKTC3114A Q7105 90M-HT400490R POWER TR 2SD2390 HVT2SD2390 Q7106 90M-HT200440R POWER TR HVT2SB1560 HVT2SB1560 Q7107 943212500020S High Voltage PNP Transistors(SOT-23)
Page 105
Ref. No. Part No. Part Name Remarks Q'ty D7601-7604 00D9430182609 DIODE 1SS133MT CVD1SS133MT D7701 943203002640S DIODE , BRIDGE(8A/600V) HVDGBJ806 D7703 90M-HD302360R DIODE ZJ6.8BT CVDZJ6.8BT D7704 00D9430182609 DIODE 1SS133MT CVD1SS133MT CAPACITORS GROUP C7101 00D9430175108 ELECT CAP 10UF 50V CCEA1HH100T C7101 943134500070S ELECT CAP 10UF 100V E2,EA,E1C CCEA2AH100TS C7102...
Page 106
Ref. No. Part No. Part Name Remarks Q'ty C7711 943134010660S ELECT CAP 470UF 6.3V CCEA0JH471T C7712 SEMICONDUCTOR CAP 0.1UF 50V ZF CCFT1H104ZF C7713 943134010660S ELECT CAP 470UF 6.3V CCEA0JH471T C7716 ELECT CAP 47UF 16V CCEA1CH470T C7717 00D9430175108 ELECT CAP 10UF 50V CCEA1HH100T C7718-7722 MYLAR CAP 0.047UF 50V...
POWER PCB UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty SEMICONDUCTORS GROUP z IC901 231010091708S I.C , OFF-LINE POWER SWITCH CVITOP258MG z IC902 963239010480S I.C , PHOTOCOUPLER CVIPC123Y22FZ0F IC903 212050010508S I.C , SHUNT REGULATOR(TO-92) CVIKIA2431AP IC931 00D2630801004 REGULATOR IC NJM7812FA HVINJM7812FA IC932 00D2630641002 REGULATOR IC NJM7912FA...
Page 109
Ref. No. Part No. Part Name Remarks Q'ty C9316 00D9430103905 ELECT CAP470UF 16V CCEA1CH471T C9317 00D9430062101 ELECT CAP 100UF 16V CCEA1CH101T C9320 00MOA10801620 CAP , ELECT(16V/1000uF) CCEA1CH102E C9321 00D9430103905 ELECT CAP470UF 16V CCEA1CH471T C9324,9325 00D9430062101 ELECT CAP 100UF 16V CCEA1CH101T C9328 943134010530S ELECT CAP 1UF 50V C CCEA1HH1R0T...
EX3AV SEMICONDUCTORS Only major semiconductors are shown. Genaral semiconductors etc. are omitted from list. The semiconductors which have a detailed drawing in a schematic diagram are omitted from list. Temp Rating EX3AV Part Number (° C) Package 1. IC's EX3AV -40 to +85 38-pin QFN T&R...
Page 112
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 113
Pin No. Mnemonic Type Description RXC_2− HDMI input Digital Input Channel 2 Complement of Port C in the HDMI Interface. RXC_2+ HDMI input Digital Input Channel 2 True of Port C in the HDMI Interface. HP_CTRLD Digital output Hot Plug Detect for Port D. 5V_DETD Digital input 5 V Detect Pin for Port D in the HDMI Interface.
Page 114
Pin No. Mnemonic Type Description PGND Ground PVDD Ground. PVDD Power PLL Supply Voltage (1.8 V). XTAL Miscellaneous Input pin for 28.63636 MHz crystal or an external 1.8 V 28.63636 MHz clock oscillator source to analog clock the ADV7623. XTAL1 Miscellaneous Crystal Output Pin.
Page 115
ADV7623 Block diagram XTAL XTAL1 VIDEO DATA RXA_C RXB_C RXC_C AUDIO DATA VIDEO DATA RXD_C RXA_0 EQUALIZER SAMPLER RXA_1 RXA_2 AUDIO DATA VIDEO DATA RXB_0 VIDEO DATA SAMPLER RXB_1 EQUALIZER RXB_2 AUDIO DATA RXC_0 AUDIO DATA EQUALIZER SAMPLER RXC_1 RXC_2 RXD_0 RXD_1 EQUALIZER...
Page 116
LC89058W-E (DIGITAL : IC402) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK LC89058W-E DV DD DGND DGND DV DD RBCK GPIO0 GPIO1 RMCK GPIO2 AGND GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 117
LC89058W-E Continued from preceding page. Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND...
Page 118
ADSP21487KSWZ3B (DIGITAL : IC404) PIN 1 GND PAD (PIN 177) at BOTTOM TOP VIEW (PINS DOWN) ADSP21487KSWZ3B Terminal Function Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. SDDQM DAI_P10 DPI_P08 FLAG0 SDCKE DPI_P07 FLAG1 DAI_P20...
Page 120
W9864G6JH-6 Block diagram CLOCK BUFFER CONTROL SIGNAL GENERATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGISTER SENSE AMPLIFIER SENSE AMPLIFIER ADDRESS BUFFER DATA CONTROL CIRCUIT BUFFER DQ31 COLUMN REFRESH COUNTER COUNTER DQM0~3 COLUMN DECODER COLUMN DECODER CELL ARRAY...
Page 121
W9864G2IH W9864G6JH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, A0−A10 Address A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 122
MX29LV160DBTI-70G (DIGITAL : IC406) BYTE# DQ15/A-1 DQ14 DQ13 Standa rd DQ12 TSOP RESET# DQ11 RY/BY# DQ10 MX29LV160DBTI-70G Block Diagram Block Diagram RY/BY# DQ0-DQ15 (A-1) Block Protect Switches Erase V oltage Generato r Input/Output Buffers State Control Program Voltage Generato r Command Chip Enable Regi s ter...
Page 128
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 14 VCL Smoothing capacitor connection pin 15 MD1 M3VPu 16 MD0 M3VPu 17 P86 (MUTE POWER) Reserve (PRE MUTE control) 18 P85 REMOTE POWER(232C) 232C POWER control pin(ON: H) 19 RES# RESET Reset input pin (reset: L) 20 XTAL...
Page 129
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 60 P81/TRSYNC FL RST FL control order pin 61 P80 S VSEL B S VIDEO switcher control pin (TC4052) MINI JACK connection detection pin for DOCK 62 BCLK/P53 iPod DET SW3VPu connection(Connection:H) 63 P52/RD#...
Page 130
Pull up/ Pin Name Symbol LvCnv STBY Function down STBY 114 P64/CS4#-B ADC RST A/D converter control pin(AK5358B) 115 P63/CS3#-A/CS7#-A E SPI REQ ETHERNET communication control pin(DM860) 116 P62/CS2#-A/CS6#-A E SPI CS N3VPu ETHERNET communication control pin(DM860) P61/CS1#/CS2#-B/ DAC MS A/D converter control pin(AK4358VQ) CS5#-A/CS6#-B/CS7#-B P60/CS0#/CS4#-A/...
Page 131
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control R2A15218FP (INPUT : IC404) BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) MUTE TRER AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB TREL ADCR SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB...
Page 132
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15218FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out,...
Page 133
The NJM2595 is designed for audio items, such as AV amplifier and others. NJM2595D NJM2595M TC4052BFT (INPUT : IC402,405) I FEATURES G 5-input 3-output G Operating Voltage ±4.0 to ±6.5V G Operating current ±15mAtyp. at Vcc=±5V G Crosstalk -65dBtyp. G Internal 6dB Amplifier G Internal 75Ω...