Onkyo TX-NR3009 Instruction Manual page 52

Speaker Configuration
This setting is set automatically by
Audyssey MultEQ ®
Speaker Setup function
you need to change the settings manually.
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
You can set the crossover frequencies, distances, and
levels of the front speakers A and front speakers B
independently. The other speakers (i.e., subwoofer, center,
surround, surround back and front high) use the same
crossover frequencies, distances, and levels for Speakers
A and Speakers B. Specify "Full Band" for speakers that
can output low frequency bass sounds adequately, for
example, speakers with a good sized woofer. For smaller
speakers, specify a crossover frequency. Sounds below the
crossover frequency will be output by the subwoofer
instead of the speaker. Refer to your speaker's manuals to
determine the optimum crossover frequencies. If you set
up your speakers using Audyssey MultEQ XT32 Room
Correction and Speaker Setup, please make sure manually
that any THX speakers are set to "80Hz(THX)" crossover.
■
Subwoofer
1ch:
Audio signal is outputted from SW1 jack only.
2ch:
Audio signal is outputted from SW1 and SW2
jacks.
No
■
Front
(Setting Speakers A and Speakers B)
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" (Speakers
B) setting is fixed to "Full Band".
• If any of "Center", "Surround", or "Front High" is set to "Full
Band", the "Front" (Speakers B) setting is fixed to "Full
Band".
■
Center , Surround
*1
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
■
Front Wide
*2*6*7*8
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None
En
52
XT32 Room Correction and
(➔ page 33). For Speakers B,
, Surround Back
*1 *2*3*4*5
, Front High
*1*2*7
Note
*1 "Full Band" can be selected only when "Full Band" is
selected in the "Front"(Speakers A) setting.
*2 If the "Surround" setting is set to "None", this setting cannot
be selected.
*3 If the "Surround" setting is set to anything other than "Full
Band", "Full Band" cannot be selected here.
*4 When the "Powered Zone 3" setting is set to "Yes", this
setting cannot be used.
*5 When "Front High + Front Wide" is set to "Yes", this
setting cannot be selected.
*6 "Full Band" can be selected only when "Full Band" is
selected in the "Front" setting.
*7
If "Bi-Amp" is selected, or the "Powered Zone 2" setting is
set to "Yes", this setting cannot be selected.
*8
If anything other than "No" is selected in "Speakers
Type(Front B)", this setting cannot be selected.
■
Surround Back Ch
1ch:
Select if only one surround back speaker L is
connected.
2ch:
Select if two (left and right) surround back speakers
are connected.
Note
• If the "Surround Back" setting is set to "None", this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
80Hz, 90Hz, 100Hz, 110Hz, 120Hz
Bypass:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency
of the LFE channel's low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
Note
• If you're using THX-certified speakers, select "80Hz".
■
Double Bass
This setting is NOT set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
(➔ page 33).
Setup function
On
Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to the
subwoofer.
Note
• This function can be set only if the "Subwoofer" setting is set to
"1ch" or "2ch", or the "Front" setting is set to "Full Band".
• If you're using THX-certified speakers, select "Off(THX)".