Hdmi; Xm Satellite Radio; Sirius Satellite Radio - Marantz SR5003 User Manual

HDMI

SYMPTOM CAUSE
The display does not The connected monitor or projector
appear over an HDMI does not support HDCP.
connection.
The HDMI input of on the TV is
not on.
The HDMI output on the source
component (DVD, Set Top Box,
etc.) is not on.
The HDMI mode is not correctly
set on the unit.
The HDMI output video resolution
of the source component (DVD,
Set Top Box, etc.) does not match
the TV specifi cations.
The device is connected with a
non-standard HDMI cable.
Power to the unit is off. (When
the unit is on standby, HDMI
connections cannot be turned
on.)
T h e c o n n e c t i o n b e t w e e n
HDMI components was not
authenticated.
The HDMI OUT RES setting does
not match that of the connected
TV.
Time is needed for the T h e c o n n e c t i o n i s b e i n g
d i s p l ay o f a n H D M I authenticated between the HDMI
connection to appear. devices.
Audio is not played The HDMI audio output of the
b a ck ove r a n H D M I source component (DVD, Set Top
connection. Box, etc.) is not on.
The signal format of the source
component (DVD, Set Top Box,
etc.) is not supported by the unit.
This unit is set to the HDMI audio
"THROUGH" mode.
DVD-Audio is not played The DVD player does not support
b a ck ove r a n H D M I CPPM, therefore it cannot output
connection. HDMI audio.
REMEDY
Be sure to use an HDCP-compatible
monitor or projector.
Set HDMI input so that it turns on, as
explained in the TV's instruction manual.
Set HDMI output so that it turns on, as
explained in the source component's
instruction manual.
Set HDMI input on the FUNC INPUT
SETUP menu as explained on page 27.
Set the resolution so that it matches, as
explained in the instruction manuals of both
components.
A 5 m or shorter cable is recommended to
ensure stable operation and prevent image
quality deterioration.
Turn on the power to the unit.
Shut off and then turn the power back on to
the unit, TV and source component.
Set the HDMI OUT RES setting to AUTO.
(See page 37.)
There is nothing wrong with the system.
Some HDMI devices require time for
authentication.
Set the HDMI audio output so that it turns
on, as explained in the source component's
instruction manual.
Set the HDMI audio output so that it can
connect to the unit, as explained in the
source component's instruction manual.
In the "THROUGH" mode, sound is not
produced from the unit. Set it to "ENABLE".
(see page 38)
• Use a DVD-Audio player that supports
CPPM.
• Turn on PCM downsampling on the DVD
player.
• Use an analog connection.

XM SATELLITE RADIO

If a problem should arise, fi rst check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there
may be a malfunction. Disconnect the power immediately and contact your store of purchase.
SYMPTOM
"TUNER" is displayed. The XM Mini-Tuner and this unit are not
properly connected.
"ANTENNA" is displayed. The XM antenna is not properly connected
to the Mini-Tuner Dock.
"NO SIGNAL" is displayed. The Signal cannot be received.
Receiving only channels 0 and 1. The XM Mini-Tuner is not activated.
"UPGRADE TUNER" is displayed. The connected XM CNP-1000 is
incompatible.

SIRIUS SATELLITE RADIO

SYMPTOM
"TUNER ERR" is displayed. SiriusConnect
connected.
"ANTENNA" is displayed Antenna is not properly connected.
"ACQUIRING" is displayed. The signal cannot be received.
"CALL SIRIUS" is displayed You have not subscribed for the selected
channel.
"FIRM UPDT" is displayed SiriusConnect
ENGLISH
CAUSE REMEDY
Check that the units are properly
connected.
Check that the antenna is properly
connected. Also, check the antenna cable
for damage.
Reposition your XM antenna.
Contact XM Satellite Radio.
(See page 49)
Upgrade the XM CNP-1000 to the XM
Mini-Tuner.
Report the model of the AV receiver and
the ID number of the CNP-1000 to XM
Listener Care. (See page 49.)
CAUSE REMEDY
TM tuner is not properly Check the 8pin mini DIN cable and AC
adapter connection are correct.
Check the antenna cable connection is
correct.
Reposition your SiriusConnect
and antenna.
Call SIRIUS if you want to subscribe.
(See page 54)
is updating software. Wait until the updating is complete.
TM
TM tuner
67