Connecting For Speaker C Use; Connection); Connecting The Remote Control Jacks - Marantz SR5003 User Manual

ENGLISH
CONNECTING FOR SPEAKER C USE (BI-AMP CONNECTION)
A bi-amp connection is possible with speakers that have two sets of inputs (for treble and bass).
This allows you to drive the treble and bass units with separate channel amps, which enables better sound
quality. Connect the speakers as shown in the fi gure. Set the SPEAKER C selector switch on the rear panel
to ON.
Notes:
• If incorrectly connected, a protective circuit in the unit will trip and set the unit to standby. (The STANDBY
indicator will fl ash.) In such case, recheck the connections between the speakers and the unit.
• Turn power to the unit off before changing the setting of the SPEAKER C selector switch.
FM FM
( ( 75 75Ω Ω ) ) GND GND AM AM ANTENNA ANTENNA
INPUT 1( ( TV INPUT 1 TV) ) INPUT 2 INPUT 2( ( DVD DVD) ) INPUT 3 INPUT 3( ( VCR VCR) ) OUTPUT OUTPUT
L L SL SL C C SBL SBL
ZONE A ZONE A TV TV DVD DVD VCR VCR DSS DSS
L L
R R
R R SR SR SW SW SBR SBR OUT OUT IN IN OUT OUT IN IN
( ( AUX 2 AUX 2) ) 7.1CH INPUT 7.1CH INPUT
RS-232C RS-232C SPEAKER C SPEAKER C SPEAKER C SPEAKER C
OFF OFF OFF OFF ON ON ON ON
L L SL SL C C SBL SBL
R R R R L L L L R R R R L L L L
FRONT A FRONT A FRONT A FRONT A FRONT B FRONT B FRONT B FRONT B
R R SR SR SW SW SBR SBR FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS
FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS FRONT A + B : 8 OHMS SPEAKER SYSTEMS SPEAKER SYSTEMS SPEAKER SYSTEMS SPEAKER SYSTEMS
PRE OUT PRE OUT
SPEAKER C SPEAKER C
OFF OFF ON ON
RIGHT
SPEAKER
Note:
• You can use surround back speaker terminals as ZONE SPEAKER A. terminals or SPEAKER C terminal when you
are not using surround back speakers.
20
INPUT 1( ( TV INPUT 1 TV) )
VIDEO VIDEO
S-VIDEO S-VIDEO
AUDIO AUDIO TV TV( ( 1 1 ) ) DVD( ( 2 2 ) ) DVD VCR IN( ( 3 3 ) ) VCR IN VCR OUT VCR OUT DSS( ( 4 4 ) ) DSS MONITOR OUT MONITOR OUT Y Y C C B B / / P P B B C C R R / / P P R R Y Y
INPUT 2 INPUT 2( ( DVD DVD) )
TAPE TAPE CD/CDR CD/CDR DIGITAL IN DIGITAL IN DIGITAL DIGITAL FLASHER IN FLASHER IN REMOTE CONT. REMOTE CONT.
REC/ZONE B REC/ZONE B
SIRIUS SIRIUS
IN IN
4 4 5 5
1 1 2 2 3 3
OUT OUT IN IN OUT OUT OUT OUT DC OUT DC OUT OUT OUT
AC OUTLETS AC OUTLETS
120V 120V 60Hz 60Hz
R R R R L L L L R R R R L L L L
UNSWITCHED UNSWITCHED
1.25A 150W 1.25A 150W
SURROUND SURROUND SURROUND SURROUND CENTER CENTER CENTER CENTER SURROUND BACK SURROUND BACK SURROUND BACK SURROUND BACK SWITCHED SWITCHED
AC IN AC IN
SPEAKER C/ SPEAKER C/ SPEAKER C/ SPEAKER C/ 1.25A 150W 1.25A 150W
ZONE SPEAKER A ZONE SPEAKER A ZONE SPEAKER A ZONE SPEAKER A

CONNECTING THE REMOTE CONTROL JACKS

DVD( ( 2 2 ) ) VD VCR IN VCR IN( ( 3 3 ) ) VCR OUT VCR OUT DSS( ( 4 4 ) ) DSS MONITOR OUT MONITOR OUT
DIGITAL IN DIGITAL IN DIGITAL DIGITAL FLASHER IN FLASHER IN
REC/ZONE B REC/ZONE B
5 5
2 2 3 3
OUT OUT DC OUT DC OUT
L L
INPUT 3( ( VCR INPUT 3 VCR) )
COMPONENT COMPONENT
VIDEO VIDEO
SURROUND BACK OUND BACK
SPEAKER C/ EAKER C/
ZONE SPEAKER A SPEAKER A
C C B B / / P P B B C C R R / / P P R R Y Y C C B B / / P P B B C C R R / / P P R R
OUTPUT 1 OUTPUT 1 OUTPUT 2 OUTPUT 2
CD recorder
REMOTE
CONTROL
MODEL NO. SR5003 MODEL NO. SR5003
IN
OUT
EXTERNAL INTERNAL
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
LEFT
control only at the unit. Also, if a Marantz power
SPEAKER
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er's, power
switch is synchronized with this unit's power switch.
Set the REMOTE CONTROL SWITCH on the back of
other units (not the SR5003) to "EXT." (EXTERNAL)
to use this feature.
INPUT 1( ( TV INPUT 1 TV) ) INPUT 3 INPUT 3( ( VCR VCR) )
COMPONENT COMPONENT
VIDEO VIDEO
2
Y Y C C / / P P C C / / P P Y Y C C / / P P C C / / P P Y Y C C / / P P C C / / P P
B B B B R R R R B B B B R R R R B B B B R R R R
INPUT 2 INPUT 2( ( DVD DVD) ) OUTPUT 1 OUTPUT 1 OUTPUT 2 OUTPUT 2
REMOTE CONT. REMOTE CONT. REMOTE CONT. REMOTE CONT.
SIRIUS SIRIUS
IN IN IN IN
OUT OUT OUT OUT
AC OUTLETS AC OUTLETS
120V 120V 60Hz 60Hz
UNSWITCHED UNSWITCHED
1.25A 150W 1.25A 150W
MODEL NO. SR5003 MODEL NO. SR5003
SWITCHED SWITCHED
AC IN AC IN
1.25A 150W 1.25A 150W
1
DVD player
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
w
Whenever external infrared sensors or similar devices
are connected to RC-5 IN of the unit, be sure to
always disable operation of the infrared sensor on the
unit by using the following procedure.
1.
Hold down the SURROUND MODE button
and the MENU button on the front panel at the
same time for fi ve seconds.
2.
The setting "IR=ENABLE" is shown on the FL
DISPLAY.
3.
Press the CURSOR buttons (1, 2) to change
this to "IR=DISABLE".
4.
Press the ENTER button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
• Be sure to set to "IR=ENABLE" when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to "IR=ENABLE".
RC OUT
OPTION
CD player
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL