Zone System - Marantz SR5003 User Manual

ENGLISH

ZONE SYSTEM

The ZONE System mode allows the same source
or different sources to be heard in two ZONEs other
than where this unit is installed.
If a surround back channel speaker or speaker C
(see page 21) are not used in the ZONE where this
unit is installed, the ZONE speaker system can be
used with the amp for the surround back channel.
This unit supports ZONE system functions such as
source selectors, ZONE speaker output, sleep timers
and remote control.
ZONE PLAYBACK USING THE ZONE OUT
TERMINALS
3.
1.
5.
3.
5.
4.
1.
Press the ZONE A or B button on the remote
controller.
60
2.
When the ZONE setting mode is engaged, one
of the following screens appears on the display
for 10 seconds.
* Display when ZONE A is selected
Z A D V D - 1 8 d B
* Display when ZONE B is selected
Z B D V D ( D 2 )
3.
Select the input source using the INPUT
SELECTOR knob on the main unit or the
function button on the remote controller.
4.
Set the ZONE volume to be used by the ZONE
system to taste either by turning the VOLUME
knob on the main unit or by pressing the
4.
VOLUME +/- buttons on the remote controller.
Note:
• The sleep timer, monaural output and other features
can also be set using the MAIN MENU.
(See page 39)
• The volume for ZONE B cannot be set on the main
unit. Control the volume by adjusting it on the amp
connected to ZONE B OUT.
5.
To cancel this function, press the ZONE A or B
button on the remote controller (after pressing
the AMP button on the remote controller).
"MULTI" indicator on the front panel will be
turned off.
ZONE PLAYBACK USING THE ZONE SPEAKER A
TERMINALS
This unit allows you to connect another set of
speakers amp and place them in a different ZONE or
separated area for Iistening to music.
3.
1.
5.
3.
5.
4.
1.
Press the ZONE SPEAKER (ZSPK) button on
the remote controller.
2.
When the ZONE SPEAKER setting mode is
engaged, one of the following screens appears
on the display for 10 seconds.
* Display when ZONE SPEAKER A is selected
Z S A D V D - 1 8 d B
3.
Select the input source using the INPUT
SELECTOR knob on the main unit or the
function button on the remote controller.
4.
Set the ZONE volume to be used by the ZONE
system to your own preference, either by
turning the VOLUME knob on the main unit or
by pressing the VOLUME +/- buttons on the
remote controller.
5.
To cancel this function, press the Z.SPKR
button on the remote controller (after pressing
the AMP button on the remote controller).
"MULTI" indicator on the front panel will be
turned off.
Note:
• The sleep timer, monaural output and other features
can also be set using the MAIN MENU. (See page
39.)
Notes for ZONE Speaker
• The ZONE Speaker mode can be set for only one of
4.
the ZONE A.
• The ZONE SPEAKER output can be used when
Surround Back Speaker = "NONE, Z-SPK" in the
SPEAKER SETUP menu. (See SPEAKER SETUP,
page 33)
• "The Surr. Back Speakers are in use" is displayed
when the ZONE SPEAKER button is pressed when
the Surround Back Speaker is not set to "NONE,
Z-SPK" in the SPEAKER SETUP menu. (See
SPEAKER SETUP, page 33)
• The ZONE speaker mode cannot be used at the same
time as the speaker C. When connecting for ZONE
use, set the SPEAKER C selector switch on the rear
panel to OFF.
• When the unit is put in ZONE SPEAKER mode and
ZSP A has been set as the Surround Back Speaker
(page 21), the ZONE SPEAKER function can be
turned on automatically simply by pressing the
SOURCE button.