Table of Contents
Advertisement
2-conduits Models
Roller Lever (Resin Lever, Resin Roller)
D4N-5@20R
D4N-6@20R
D4N-7@20R
D4N-8@20R
Blue
Resin lever
14 dia.
34
5.4
± 0.1
20
± 0.1
22
2.15±0.05R
± 0.1
40
mounting
± 0.1
42
holes
Conduit cap
± 0.2
42
(See note 3.)
56 max.
Adjustable Roller Lever, Form Lock
(with Metal Lever, Rubber Roller)
D4N-5@2HR
D4N-6@2HR
D4N-7@2HR
D4N-8@2HR
Resin bearing
Blue
34
5.4
2.15±0.05R
mounting holes
Conduit cap
(See note 3.)
Note: 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
2. Variation occurs in the simultaneity of contact opening/closing operations of 2NC and 3NC contacts. Check contact operation.
3. There are a minimum of five turns of the screw thread for a Pg13.5 conduit opening and four turns minimum for a G 1/2 conduit opening.
Model
D4N-@@20R
LF max.
6.4 N
LT max.
55°
PT 1
18° to 27°
(See note 2.)
(PT 2)
(44° )
(See note 3.)
(TT)
80°
(See note 4.)
DOF min.
20 N
(See note 5.)
DOT min.
50°
(See note 5.)
D4N-@R
± 1
47
40
± 1
17.5 dia. × 6.8
(27)
resin roller
11
± 0.2
26R
20.5 × 20.5
2.5
43.5
16.7
21.5
9
± 0.2
20.5
39
± 0.2
25 dia.
47
(3)
14.2
30
36
+0.15
Two, 4
dia. holes
0
Depth: 5
48.2
± 1
± 1
41.3
50 dia. × 8
(29.2)
rubber roller
11
± 0.2
32 to 66R
(P:2)
Stainless
25
steel lever
2.5
21.5
± 0.2
9
20
± 0.1
39
± 0.2
± 0.1
22
25 dia.
47
± 0.1
40
± 0.1
42
± 0.2
42
(3)
14.2
56 max.
30
D4N-@@2GR
D4N-@@2HR
5.6 N
5.4 N
55°
55°
18° to 27°
18° to 27°
(44° )
(44° )
80°
80°
20 N
20 N
50°
50°
Adjustable Roller Lever, Form Lock
(with Metal Lever, Resin Roller)
D4N-5@2GR
D4N-6@2GR
D4N-7@2GR
D4N-8@2GR
Blue
34
5.4
2.15±0.05R
Cap
mounting holes
Conduit cap
(See note 3.)
20.5 × 20.5
14 dia.
43.5
16.7
20.5
Cap
+0.15
Two, 4
dia. holes
0
Depth: 5
Note: 1. Variation occurs in the simultaneity of contact opening/clos-
ing operations of 2NC, 2NC/1NO, and 3NC contacts. Check
contact operation.
2. These PT values are possible when the NC contacts are
open (OFF).
3. These PT values are nominal values possible when the NO
contacts are closed (ON). (1NC/1NO models only)
4. Nominal value.
5. Load and stroke values for the direct opening mechanism.
For safe use, always make sure that the minimum values or
greater are provided.
± 1
45
39.5
± 1
17.5 dia. × 6.8
(31)
resin roller
11
± 0.2
20 to 66R
25
2.5
21.5
± 0.2
9
39
± 0.2
±
20
0.1
25 dia.
±
47
22
0.1
±
40
0.1
±
42
0.1
42
± 0.2
(3)
14.2
56 max.
30
Two, 4
Depth: 5
20.5 × 20.5
14 dia.
43.5
16.7
20.5
Cap
+0.15
dia. holes
0
G-275
Advertisement
Table of Contents
