Operation - Parkside ZKGS 2100 UG Operation And Safety Notes

Anleitung_4300696:_ 10.07.2009
Mount the workpiece support (9) on the
fixed saw table (17) and tighten the
appropriate locking screw (10) (Figure 5).
Mount the second workpiece support (9) on
the opposite side of the saw and secure
with the appropriate locking screw (10).
When the locking screw (23) is loosened,
you can tilt the machine head (5) to the left
by up to 45°.
Screw the additional stability bar (18) to the
back of the equipment. (Figure 6)
7.3 Final adjustment of the stop for
crosscut 90° (Fig. 7-8)
An angular stop is not supplied.
Fasten the turntable (16) in 0° position.
Undo the securing screw (23) and tilt the
machine head (5) as far to the right as
possible using the handle (1).
Place the 90° angular stop (z) between the
saw blade (7) and the turntable (16).
Slacken the counternut (d). Adjust the
adjustment screw (29) until the angle
between the blade (7) and the turntable
(16) equals 90°.
Retighten the counter nut (d) to secure this
setting.
Check the position of the pointer (21) on
the scale (20). If necessary, release the
pointer (21) with a crosstip screwdriver,
move to the 0° position of the scale (20)
and retighten.
7.4 Final adjustment of the stop for meter
cut 45° (Fig. 1, 7, 10 – 11)
An angular stop is not supplied.
Fasten the turntable (16) in 0° position.
Undo the securing screw (23) and tilt the
machine head (5) to the right to an angle of
45° using the handle (1).
Place the 45° stop angle (y) between the
blade (7) and the turntable (16).
Adjust the adjustment screw (30) until the
angle between the saw blade (7) and the
turntable (16) is 45°.
12:31 Uhr Seite 17
7.5 Assemble base frame (Fig. 26)
Construct the base frame as shown in Fig.
26.
Insert a screw (42) from outside, through
the parts to be joined, then secure this with
a washer (43), a spring washer (44) and a
nut (45).
All nuts should only be attached at the end
in order to prevent tension in the base
frame.
Finally, cover the supporting feet with the
rubber stops.
7.6 Assembly of the saw on the frame
(Fig. 27-30)
Anti-slip protection on the underside of the
saw should be removed and kept in a safe
place.
Place the saw on the base frame so that the
4 oval holes on the base frame coincide
with the mounting holes on the saw.
Secure all 4 bolts on the base frame so that
they are tight.

8. Operation

8.1 Crosscut 90° and turntable 0°-45°
(Fig 1–3, 12)
Important! The integral resetting springs will
automatically lift the machine head. Do not
simply let go of the handle (1), but allow the
machine head (5) to rise slowly, applying slight
counterpressure as it does so.
For cutting widths up to approx. 100 mm it is
possible to fix the saw's drag function with the
locking screw for drag guide (24) in rear
position. If the cutting width exceeds 100 mm
you must ensure that the locking screw for
drag guide (24) is slackened and that the
machine head (5) can be moved.
Move the machine head (5) to its upper
position.
Push the machine head towards the rear
(5) with the handle (1) and, wherever
necessary, fasten it in this position
(according to cutting width).
Place the piece of wood to be cut at the
GB/IE/
CY
17