Parkside ZKGS 2100 UG Operation And Safety Notes page 18

Anleitung_4300696:_ 10.07.2009
GB/IE/
CY
stop rail (19) and on the turntable (16).
Fasten the material with the clamping
device to the immobile sawing table (17) to
prevent movement during the cutting
process.
Push the release lever (3) to release the
machine head (5).
Push the ON-OFF switch (2) to switch on
the motor.
For fixed drag guidance (26), move the
machine head (5) with the handle (1)
evenly and with light pressure downwards,
until the saw blade (7) has cut through the
workpiece.
With the drag guide (26) not fixed in place:
Pull the machine head (5) all the way to the
front. Lower the handle (1) to the very
bottom by applying steady and light
downward pressure. Now push the
machine head (5) slowly and steadily to the
very back until the saw blade (7) has
completely cut through the workpiece.
Once the sawing process is over, let the
machine head (5) move back into the upper
resting position and let go of the ON/OFF
switch (2)
8.2 Crosscut 90° and turntable 0°-45°
(Fig 1-3, 13)
With the crosscut saw it is possible to make
crosscuts of 0° - 45° to the left and 0° - 45° to
the right up to the stop rails.
Release the turntable (16) by slackening
the locking grip (13).
Press the latched position lever (12). Turn
the turntable (16) and scale pointer (14) to
the desired angular setting on the scales
(15) and lock into place with the locking
grip (13). The saw has locking positions at
angles of - 45°, -30°, -22,5°, -15°, 0°, 15°,
22,5°, 30° and 45°, at which you can
engage latched position lever (12).
Cut as described under Section 8.1.
18
12:31 Uhr Seite 18
8.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1 – 3, 14)
The crosscut saw can be used to make miter
cuts of 0° - 45° in relation to the work surface.
Remove the clamping device (8) if
necessary or fit it on the opposite side of the
fixed saw bench (17).
Move the machine head (5) to its upper
position.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23). Use the
handle (1) to tilt the machine head (5) to
the left until the pointer (21) points to the
required angle on the scale (20).
Re-tighten the fixing screw (23).
Cut as described in section 8.1.
8.4 Crosscut 90° and turntable 0°-45°
(Fig 1–3, 15)
The crosscut saw can perform mitre cuts at an
angle of 0°-45° to the work surface and at the
same time at an angle of 0°-45° left or right of
the stop rail (double mitre cuts)
Disassemble the clamping device (8)
whenever necessary or assemble it on the
other side of the immobile sawing table
(17).
Move the machine head (5) to its upper
position.
Release the turntable (16) by slackening
the locking grip (13).
Press the latched position lever (12). Turn
the turntable (16) and scale pointer (14) to
the desired angular setting on the scale
(15) and lock into place with the locking
grip (13).
Loosen the locking screw (23) and tilt the
machine head (5) with the handle (1) to the
left, to the desired angle (see also Section
8.3).
Re-tighten the locking screw (23).
Cut as described under Section 8.1.
8.5 Limiting the cutting depth (Fig. 16)
The cutting depth can be infinitely adjusted
using the screw (27). To do this loosen the
knurled nut on the screw (27). Move the
stop for the cutting depth limiter (28) to the
outside. Turn the screw (27) in or out to set