Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 9 1. Introduction 2.2 General safety instructions for electrical equipment Important! Important! When using electrical tools, the When using equipment, a few safety following safety measures are to be taken precautions must be observed to avoid injuries to prevent electric shocks, injuries and risk and damage.
Page 10
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 10 10.Don't abuse cord Damaged safety devices and parts must be – Never carry tool by cord or yank it to repaired or replaced by experts in a disconnect it from receptacle. Keep cord customer service workshop, unless from heat, oil and sharp edges.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 11 speed steel (HSS Steel) may not be used. machine immediately. There is a risk of leakage! 2. Safety instructions for the Laser Always replace all batteries at the same time. Only replace with new batteries of the Important: same type.
Page 12
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 12 Take care to only use the spacers and given in the user manual. spindle rings which are made by the The arrow on the saw blade must line up manufacturer for this specific purpose. with the appropriate arrow on the If the machine is fitted with a laser, this equipment.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 13 or maintenance work done. 23. Locking screw The safety, work and maintenance 24. Locking screw for drag guide instructions from the manufacturer, as well 25. Safety pin as the measurements in the technical data, 26.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 14 result of this. The appliance can lead to temporary fluctuations in voltage if the mains supply is Please note that our equipment has not been unreliable. designed for use in commercial, trade or The product is only to be used at sockets industrial applications.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 15 Idle speed 7.2 Assembling the saw (Fig 1-3, 5-6) Screw together the locking grip (13) and Sound pressure level L 86 dB(A) mounting thread (e). Sound power level L 99 dB(A) To adjust the turntable (16), loosen the locking grip (13) by approx.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 16 between the blade (7) and the turntable Fasten the material with the clamping (16) equals 90°. device to the immobile sawing table (17) to prevent movement during the cutting Retighten the counter nut (d) to secure this process.
Page 17
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 17 8.3 Miter cut 0°- 45° and turntable 0° the required cutting depth. Then re-tighten (Fig. 1 – 3, 14) the knurled nut on the screw (27). The crosscut saw can be used to make miter Check the adjustment by making a test cut.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 18 8.8 Transport (Fig. 1 – 3) 10. Cleaning, maintenance and Tighten the locking grip (13) to lock the ordering of spare parts turntable (16). Press the release lever (3), push the Always pull out the mains power plug before machine head (5) to the rear and lock it with starting any cleaning work.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 19 11. Disposal and recycling equipment without any electrical components which are included with the used device. The unit is supplied in packaging to prevent its being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system.
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 21 13. GUARANTEE CERTIFICATE Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card.
Page 22
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 22...
Page 23
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 23...
Page 24
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 24...