Assigning Parameters To Control Changes - Yamaha S Rev1 Owner's Manual

Assigning Parameters to Control Changes

Reverb Balance and Reverb Level parameters for each channel can be assigned to MIDI
Control Changes 0 through 95.
Use the [UTILITY] button to locate the MIDI page.
1
Use the cursor buttons to select the REV BALANCE or REV LEVEL assignments
2
in the CONTROL CHANGE section of the page.
In 2-channel mode, these are L-CH and R-CH. In 4-channel mode, Front-L, Front-R,
Rear-L, and Rear-R. And in 2-channel x2 mode, A-L, A-R, B-L, and B-R.
Use the DATA wheel or [–1/DEC] and [+1/INC] buttons to assign a Control
3
Change to OFF or 0 through 95.
When a Control Change message is received, the assigned parameter is controlled. If the
Rev page is selected, you can see the parameter value update, and if the parameter is the
currently selected parameter, then the corresponding fader moves as well.
If a Control Change is assigned to more than one parameter, all the assigned parameters
are controlled when that Control Change is received.
Since Control Changes are assigned to channels individually, they are not affected by
the GROUP button on the Rev page. Even if channels are grouped, only the assigned
channel parameter is controlled when a Control Change message is received.
If a page selected by using the [PARAMETER FINE] button is displayed when a Control
Change message is received, the corresponding fader moves and the graph and param-
eter values change, causing the Edit status indicator to appear.
If a page selected by using the [PARAMETER MAIN] button is displayed when a Con-
trol Change message is received, the corresponding fader, graph, and parameter value
do not change. Only the Edit status indicator appears. To update the fader, graph, and
parameter value, select another page, then select the previous page again.
The following illustration shows the type of MIDI equipment that can be used with the
SREV1 for remote parameter control using Control Change messages.
SREV1
MEMORY CARD

Assigning Parameters to Control Changes

POWER
INPUT OUTPUT FS LOCK
CLIP 48K MIDI IN
1 2 3 4 CH 1 2 3 4
44.1K
SIGNAL
ON OFF
CD-ROM
MIDI keyboard
MIDI mixer
PHANTOM +48V OFF ON
INPUT (BAL)
PAD
26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB
–16 –60 –16 –60 –16 –60 –16 –60 –16 –60 –16 –60 –16 –60 –16
+10 GAIN –34 +10 GAIN –34 +10 GAIN –34 +10 GAIN –34 +10 GAIN –34 +10 GAIN –34 +10 GAIN –34 +10 GAIN
1 2 3 4 5 6 7 8
UTILITY MIDI SETUP VIEW
FUNCTION
MIDI Sampler PAN/
DYNAMICS EQ/ATT Ø/DELAY ROUTING MEMORY
FADER MODE
EFFECT 1 EFFECT 2 OPTION I/O REMOTE 1 RETURN 2
AUX 1 AUX 2 AUX 3 AUX 4
HOME
1 2 3 4 5 6 7 8 9
17 18 19 20 21 22 23 24
SEL SEL SEL SEL SEL SEL SEL SEL SEL
SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO
ON ON ON ON ON ON ON ON ON
6 6 6 6 6 6 6 6 6
0 0 0 0 0 0 0 0 0
5 5 5 5 5 5 5 5 5
10 10 10 10 10 10 10 10 10
20 20 20 20 20 20 20 20 20
40 40 40 40 40 40 40 40 40
60 ∞ ∞ 60 ∞ 60 ∞ 60 60 ∞ 60 ∞ 60 ∞ ∞ 60 60 ∞
MIDI controller 1 2 3 4 5 6 7 8 9
17 18 19 20 21 22 23 24
SREV1—Owner's Manual
71
PHANTOM +48V OFF ON
–10dBV (UNBAL)
13 15 L
R
14 16
IN OUT
2TR
PHONES
26dB 26dB 26dB 26dB 15/16 MONITOR
2TR IN 2TR IN
–60 –16 –60 –16 –60 –16 –60 –16 –60 +10 –20 +10 –20 0 10 0 10
–34 +10 GAIN –34 +10 GAIN –34 +10 GAIN –34 +10 GAIN –34 GAIN GAIN LEVEL LEVEL
MONITOR
9 10 11 12 13/14 15/16 OUT PHONES
DIGITAL MIXING CONSOLE
EQ HIGH L STEREO R
PAN CLIP
–3
PAN HI-MID –6
–9
F F –12
–15
LO-MID –18
G –24
–30
–36
–42
G LOW –48
SELECTED CHANNEL
10 11 12 13/14 15/16 STEREO
MASTER 1 RETURN 2
SEL SEL SEL SEL SEL SEL SEL SEL SOLO
SOLO SOLO SOLO SOLO SOLO SOLO SOLO
ON ON ON ON ON ON ON ON MEMORY
–1/DEC +1/INC
PARAMETER
6 6 6 6 6 0
–5
0 0 0 0 0 –10
–15
5 5 5 5 5
–20
CURSOR
10 10 10 10 10 –30
20 20 20 20 20 –40
–50
40 40 40 40 40 –70
∞ 60 60 ∞ 60 ∞ 60 ∞ 60 ∞ – ∞
ENTER
10 11 12 13/14 15/16 STEREO
MASTER