Specifications - Yamaha EMX3500 Operation Manual

SPECIFICATIONS

Maximum Output Power
350W+350W/4Ω, 200W+200W/8Ω, 0.5% THD at 1kHz
Total Harmonic Distortion
Channel Input to Post-GEQ OUT
Less than 0.1%, 20Hz — 20kHz, +4dB output
Post-GEQ IN to SPEAKER OUT
Less than 0.1%, 20Hz — 20kHz, 175W output into 4Ω
Frequency Response
+1, -3dB, 20Hz — 20kHz, 1W into 4Ω
Hum & Noise (Average, Rs=150Ω, w/BPF 20Hz — 20kHz)
-128dB Equivalent Input Noise
-96dB Residual Output Noise (Pre-GEQ Out)
-96dB Residual Output Noise (Effect Send, Monitor
Out)
-73dB Residual Output Noise (Speaker Out)
-90dB (Pre-GEQ)
Master fader at maximum level and all channel
switches OFF.
-80dB (EFFECT SEND)
Master fader at maximum level and all channel
EFFECT controls at minimum level.
-83dB (MONITOR OUT)
Master VR at maximum level and all channel
MONITOR controls at minimum level.
Maximum Voltage Gain
64dB CH IN to Pre-GEQ OUT
64dB CH IN to MONITOR OUT A, B
70dB CH IN to EFFECT SEND 1 — 2
0dB EFFECT RETURN 1, 2 to Pre-GEQ OUT
0dB EFFECT RETURN 1, 2 to MONITOR OUT
12dB TAPE IN 1, 2 to Pre-GEQ OUT
10dB CD IN to Pre-GEQ OUT
31dB Post-GEQ IN to SPEAKER OUT at 8Ω
When Post-GEQ IN level is +4dB, SPEAKER
OUT level is full power.
Crosstalk (at 1kHz)
70dB Adjacent input channels
70dB Input to Output
Input Channel Gain Control
44dB variable from -60dB to -16dB
Input Channel PAD Switch
0/20dB of attenuation
Input Channel Select Switch
A or B (XLR/PHONE)
Input Channel Equalization
±15dB maximum boost or cut in each band
High: 12kHz shelving
Mid: 250Hz — 5kHz peaking
Low: 80Hz shelving
Turnover/Rolloff frequency of shelving: 3dB below
maximum variable level.
Input Channel HPF Switch
80Hz, 12dB/oct.
Graphic qualizer
±12dB maximum boost or cut in each of nine bands:
63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k Hz
CD Select Switch
CD A or B
Level Meters
2 Illuminated meter (0VU=175W/4Ω)
CH Peak Indicators
Red LED on each channel turns ON when post-EQ signal
reaches the level 3dB below clipping.
CH Signal Indicators
Green LED on each channel turns ON when post-EQ
signal reaches -10dB.
Phantom Power
+48V is supplied to electrically balanced inputs to power
condenser microphones via 6.8kΩ current limiting/
isolation resistors.
Digital Effect
15 program selection
Power Requirement
U.S & Canada: 120V, 60Hz
General model: 230V, 50Hz
Power Consumption
U.S & Canada: 600W, 750VA
General model: 600W
Dimensions (W x H x D)
12ch model: 684 x 240 x 628 mm
16ch model: 816 x 240 x 628 mm
Weight
12ch model: 34kg
16ch model: 39kg
Note: 0dB = 0.775Vrms.
Specifications and appearance subject to change without
notice.
15