Table of Contents
Advertisement
We strongly recommend that a periodic maintenance
schedule is adhered to. However, if you wish to have the
maintenance carried out by a trained technician please
contact your local Tunturi dealer for details of service
available and charges.
Check from time to time that all fasteners are properly
tightened and wiring is in place. To avoid damaging
fasteners, do not overtighten.
CLEANING THE RUNNING BELT
Turn the unit off and unplug the electrical cord from the wall
outlet and from the treadmill. Carefully turn the treadmill on
its side.
Wipe off the inside of the running belt using a harsh brush.
Do not use solvents.
Rotate the running belt carefully by hand to clean the entire
inside face. Loosen the belt adjusting screws at the back of
the treadmill, if necessary. Return the treadmill into the
upright position.
If running belt edges are frayed, check the running belt
alignment.
CLEANING THE TREADMILL
Wipe the treadmill surfaces, especially the handlebars and
meter from dust with a damp cloth or towel. Do not use
solvents.
Use a small vacuum nozzle to carefully vacuum around all
visible components (belt, running deck, side rails etc.). By
supporting the device on one of the side rails you can also
vacuum it from below. Vacuum also from inside the motor
hood.
Clean both the treadmill's rollers once a year as follows:
loosen both the roller's adjusting bolts and clean the roller
with a roughish brush. Tighten the adjusting bolts and check
that the belt sits in the middle and is tight enough.
LUBRICATING THE RUNNING DECK
NOTE! Lubrication is the most important service activity
for the treadmill.
This is absolutely essential, if the friction of the running deck
increases noticeably or the motor begins to heat up. Ensure
after every 50 hours of use that both the belt and the running
deck are moist with lubricant. Insufficient lubrication will
cause the belt, running deck and motor to wear out and
break.
The need for relubrication depends to a great extent on the
running styles and weight of the user: heavy user weight and
slow speed put particular strain on the device and therefore
demand greater lubrication. Use only T-Lube lubricant to
lubricate the treadmill. Contact your local Tunturi dealer for
further supplies of T-Lube.
NOTE! The device must under no circumstances be
lubricated with silicone!
1.
Let the treadmill run at 5 km/h (3 mph).
2.
Spray T-Lube directly to the underside of the running
belt for 5 seconds; the amount corresponds to 10ml.
3.
Ensure that a strip of about 20 cm/8" wide on the
underside of the running belt becomes moist with
T-Lube along its whole length. The treadmill is
instantly ready for use.
ERROR CODES
In case of certain faults relating to the electronics of the
treadmill, it has an integral, internal fault-finding system in
order that faults can be found and corrected as quickly as
possible.
The fault-finding system obviously does not cover all
possible faults, but it does help to identify the most likely
faults resulting from long-term use. When such a fault
occurs, the display shows one of the following error codes:
CODE
DESCRIPTION
E 1
Failure of speed sensor (sensor does not
detect belt movement)
E 4
Lift sensor or elevation system failure
E 7
Software failure
E 8
Speed of the running belt exceeds set
speed
If any error code appears on the display or there are other
malfunctions, proceed as follows:
1.
Turn off the power switch for a minute and then
turn it on again.
2.
Insure the tether key is properly inserted.
3.
Insure the power cord is properly plugged.
4.
Insure the treadmill is properly lubricated.
5.
If the error code does not disappear after the
above mentioned maintenance actions, please
contact your local Tunturi dealer. Always give
the error code and serial number.
tEtH
The tether key is not properly inserted
NOTE! If you notice a malfunction during use, contact the
dealer. Always give the model and serial number of your
device. Please state also the nature of the problem, conditions
of use and purchase date.
In spite of continuous quality control, individual defects and
malfunctions may occur due to individual components. It is
in most cases unnecessary to take the whole treadmill for
repair, as it is usually sufficient to replace the defective part.
9
Advertisement
Table of Contents
