Controlling External Components - Yamaha YSP-4100 Owner's Manual

A
B
C
TV TV AV AV
Depending on the external AV component you are using, you may not be able to operate the component with the remote control, even if
TV TV AUX 1 AUX 1 AUX 2 AUX 2
a remote control code is set. In this case, operate the component using the supplied remote control.
D
HDMI 1 HDMI 1 HDMI 2 HDMI 2 HDMI 3 HDMI 3
HDMI 4 HDMI 4 iPod iPod RADIO RADIO
ENTER
You can control external components using the following
MOVIE MUSIC TAINMENT OFF
keys on the remote control of this unit by setting the
CINEMA DSP
SURROUND STEREO
appropriate remote control codes (page 49). Before
operating the control keys, press one of the DInput
G
ENTER ENTER
selector keys to select an external component to be
controlled.
H
TOP MENU TOP MENU MENU MENU
I
OPTION OPTION SETUP SETUP RETURN RETURN
B TV p
J
TV VOL CH VOLUME
Turns on the power of your TV or set it to the standby
K
mode.
TV TV L
MUTE MUTE INPUT INPUT MUTE MUTE
B AV p
UNIVOLUME SUR. DECODE INTELLIBEAM
Turns on the power of the selected component or set it to
1 1 2 2 3 3
the standby mode.
4 4 5 5 6 6
N
7 7 8 8 9 9
0 0 +10 +10 G Cursor (
ENT ENT
CODE SET
O
Use to select menu items.
P
H TOP MENU
TUNING PRESET CATEGORY
Displays the top menu of a Blu-ray disc or DVD.
INFO MEMORY MEMORY SLEEP
H MENU
Displays the menu of a Blu-ray disc or DVD.
I RETURN
Returns to the previous menu screen.
J CH
Switches between available channels for your external
component.
L TV operation keys
ATransmission
indicator
BAV
N Numeric keys
BTV
Use to enter numeric digits or specify a channel number.
CPower
O CODE SET
DInput selector keys
Sets remote control codes for external component
GCursor (
/ / /
operations (page 42).
) keys
P External component operation keys
GENTER
Use to control playback of your external component.
HMENU
y
HTOP MENU
• The BTVp and LTV operation keys always work regardless
IRETURN
JCH
/
KMUTE
• Depending on external components, some or all operations may
KVOLUME +/–
LTV operation keys
NNumeric keys • If you operate your TV with the remote control of this unit
OCODE SET
PExternal component
operation keys
42
En
Note
/ / / ) keys, ENTER
/
TV VOL +/–
Adjusts the audio output level of your TV.
TV MUTE
Temporarily mutes audio output from your TV.
TV INPUT
Switched the input source for your TV.
of the selected input source.
Notes
not work. In this case, operate the component using the supplied
remote control.
when the HDMI control function is activated, this unit or
external component connected to this unit with HDMI works
improperly in some cases.

Controlling external components

■ Setting remote control codes
1
While holding down OCODE SET, press
DInput selector key to which the remote
control code is assigned.
ATransmission indicator flashes twice.
2
Release OCODE SET.
3
Press NNumeric keys to enter the remote
control code (page 49) for your external
component.
Each time you press you press the key,
ATransmission indicator flashes once. Once the 5-
digit remote control code is entered properly,
ATransmission indicator lights up for approximately
2 seconds.
y
• To clear remote control code set to a selected input source,
enter "00010".
Note
• If any key other than NNumeric keys is pressed,
ATransmission indicator flashes 5 times and the setting
mode is canceled.
4
Perform a test operation using the remote
control of this unit.
If the external component functions correctly, the
remote control code setup is successful. If it does not
function correctly, the remote control code may be
incorrect. Check the remote control code for your
external component (page 49) and try again.
Note
• If no operation is performed after step 1 or in the middle of
step 2 within 30 seconds, ATransmission indicator
flashes 5 times and the setting mode is canceled.
■ Resetting all remote control codes
1
While holding down OCODE SET, press
ISETUP.
ATransmission indicator flashes twice.
2
Release OCODE SET.
3
Press NNumeric keys to enter "99999".
Each time you press the NNumeric keys,
ATransmission indicator flashes once. Once the
remote control code is entered properly,
ATransmission indicator lights up for approximately
2 seconds and then the initialization is completed.
Note
• If one of the other keys is pressed, ATransmission
indicator flashes 5 times and the initialization is canceled.