Basic Set Menu Operation; Manual Setup - Yamaha YSP-4100 Owner's Manual

1
TV AV
TV TV AUX 1 AUX 1 AUX 2 AUX 2
D
HDMI 1 HDMI 1 HDMI 2 HDMI 2 HDMI 3 HDMI 3
HDMI 4 HDMI 4 iPod iPod RADIO RADIO
ENTER
MOVIE MUSIC TAINMENT OFF
CINEMA DSP
SURROUND STEREO
G
ENTER ENTER
TOP MENU MENU
I
OPTION OPTION SETUP SETUP RETURN RETURN
2
TV VOL CH VOLUME
TV TV
MUTE INPUT MUTE
UNIVOLUME SUR. DECODE INTELLIBEAM
1 2 3
4 5 6
7 8 9
0 +10
ENT
CODE SET
TUNING PRESET CATEGORY
INFO MEMORY SLEEP
3
4
Use this menu to manually adjust the parameters related to
the sound beam output. To fine-adjust parameters
configured by AUTO SETUP, use "BEAM
ADJUSTMENT" and "IMAGE LOCATION".
■ SETTING PARAMETERS (Setting
SET MENU → MANUAL SETUP → SETTING
PARAMETERS
Use to set the position of this unit in your listening room
and the distance of this unit from the listening position.
y
• If you make adjustments in "SETTING PARAMETERS", the
DInput selector keys
GENTER
G
/ / /
G
/
• If you make adjustments in "SETTING PARAMETERS", the
G
IRETURN
ISETUP
34
En

Basic SET MENU operation

Press ISETUP.
SET MENU
. ;MEMORY
;AUTO SETUP

;MANUAL SETUP

;SOUND SET MENU
;SOUND OUT MENU
;INPUT MENU
;DISPLAY MENU
[ ]/[ ]:Up/Down
[ENTER]:Enter
Press G
/ to select the desired menu
and then press GENTER.
C)MANUAL SETUP
.
1)SETTING PARAMETERS
2)BEAM ADJUSTMENT
3)IMAGE LOCATION
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
• To return to the previous menu, press IRETURN.
Press G
/ / /
configure each parameter.
y
• The initial settings are marked with "*".
Note
• The menu screen disappears if one of the DInput selector
keys is pressed while the SET MENU is being configured.
To exit from the menu, press ISETUP.
MANUAL SETUP
parameters)
"BEAM ADJUSTMENT" parameters are automatically
adjusted.
Note
beam optimization settings made in the AUTO SETUP
procedure will be lost.
and GENTER to
1
In "SETTING PARAMETERS 1/3", configure
"INSTALLED POSITION".
Select the installed position of this unit.
Choices: FLAT TO WALL* (parallel to wall),
ANGLE TO WALL OR CORNER (angle to wall or
corner)
FLAT TO WALL
Note
• If you change this setting, "BEAM MODE" setting
changes automatically (page 23).
2
Configure "INSTALLED HEIGHT".
Specify the installed height of this unit.
Control range: 0.0 m to 3.0 m (0.0 ft to 10.0 ft)
Initial setting: 1.0 m (3.5 ft)
y
• Press G
to proceed to the next page.
3
In "SETTING PARAMETERS 2/3", configure
the listening room settings.
Specify the length and width of the listening room.
Control range: 2.0 m to 12.0 m (6.5 ft to 40.0 ft)
When this unit is
installed parallel to wall,
specify the width of the
listening room and the
distance between this
unit and rear wall.
When this unit is
installed at the corner of
the room, specify the
width of length of the
listening room.
4
In "SETTING PARAMETERS 3/3", configure
the distance settings.
Specify the distance between the listening position
and this unit. When this unit is installed parallel to
wall, you also need to specify the distance between
the listening position and left wall.
ANGLE TO WALL OR
CORNER
0.0 to 3.0 m
(0.0 ft to 10.0 ft)