Xerox DocuTech 128 Install Manual

Installation Preparation Document
Xerox DocuTech 128/155/180 HighLight Color
The main DocuTech 128/155/180 HLC components are:
• TM
Sun Blade 2500 Controller
•
CD/DVD combo drive
•
color flat panel monitor
•
keyboard and mouse
•
Ethernet interface (10/100/1000 BaseT)
•
Three printer interface cards
•
Controller Stand
•
Options
•
18/36 track tape drive
•
Online connection
•
QIC tape
•
USB floppy disk drive
or
•
Sun W1100Z (AMD) contoller
•
CD/DVD combo drive
•
color flat panel monitor
•
keyboard and mouse
•
Ethernet interface (10/100/1000 BaseT)
•
Three printer interface cards
•
Controller Stand
•
Options
•
18/36 track tape drive
•
Online connection
•
QIC tape
•
USB floppy disk drive
•
Solaris 10 and DocuSP print services software
•
Printer
•
Black plus one highlight color*
•
Xerographic engine with laser raster imaging system for
black and Light Emitting Diode for color
•
Permanent housing for black dry ink; customer changeable
unit (CCU) for color dry ink
•
Prints simplex or duplex
•
Inverter Feeder/Stacker and up to 3 additional
feeder/stackers
•
Optional Bypass Transport to provide connection to
additional finishers
* Additional dry inks, not listed on this document, will be customer
options as they become available, and will be offered under standard
Xerox terms and conditions.
701P46159
October 2006
(for physical installation of the product only)
Space Requirements / Service Space Envelope
The dimensions shown below are absolute minimums.
Configuration Width
With inverter 173.3
feeder/stacker (in)
and one 433.3
feeder/stacker (cm)
With inverter 205.6
feeder/stacker (in)
and two feeder 511.3
stackers (cm)
With inverter 237.9
feeder/stacker (in)
and three 594.4
feeder/stackers (cm)
Optional Bypass 20.4 (in)
Transport* 51 (cm)
•
The minimum total space required includes the required space
necessary for the Xerox service personnel to service the printer.
•
A minimum of 78 inches/198 cm clearance from the floor to the
nearest overhead obstruction must be maintained.
•
The printing system must be installed in a fixed location.
•
Space requirements for the controller stand are 36 x 36
inches/91 x 91 cm.
•
For proper operation, the printer must be perfectly level. On
floors less than two degrees out of level, a leveling kit must be
used to level the equipment. The printer will not function
properly on floors more than two degrees out of level.
•
For detailed space requirements and diagrams, refer to the
DocuTech 128/155/180 HighLight Color Installation Planning
Guide.
Electrical Requirements (printer)
The printer requires:
•
60 HZ service (2 cords required)
Voltage
Amperage (dedicated)
Cycles
Receptacle Xerox Part No.
Receptacle NEMA Part No.
Receptacle Diagram
Power Cord Kit Number
Power Cord Length
Depth Min total Weight
req'd
Width x
depth
48.8 (in) 262.5 x 3164 lbs
122 131.5 (in) 1438 kg
(cm) 631.3 x
328.8
(cm)
48.8 (in) 294.8 x 3685 lbs
122 131.5 (in) 1675 kg
(cm) 737 x
328.8
(cm)
48.8 (in) 327.1x 4206 lbs
122 131.5 (in) 1912 kg
(cm) 817.8 x
328.8
(cm)
28.3 (in) 176 lbs
71 (cm) 80 kg
MultiSource
2-phase, dual power cord
configuration
208/240 208/240
(4 wire)
50 30
60 Hz 60 Hz
14-50R 14-30R
15 feet 15 feet
(4 wire)