Xerox Nuvera 100 EA Operator's Manual
Hide thumbs
Also See for Nuvera 100 EA:
- Brochure (12 pages) ,
- Product safety data sheet (2 pages) ,
- Paper manual (70 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Xerox Nuvera 100 EA
Summary of Contents for Xerox Nuvera 100 EA
- Page 1 January 2015 702P00782 Xerox Nuvera ® Xerox Production Stacker Operator Manual Xerox Nuvera ® 100/120/144/157 EA Production System Xerox Nuvera ® 100/120/144 MX Production System Xerox Nuvera ® 200/288/314 EA Perfecting Production System Xerox Nuvera 200/288 MX Perfecting Production System...
- Page 2 ©2012 Xerox Corporation. All rights reserved. XEROX ® , XEROX and Design ® and Xerox Nuvera ® trademarks of Xerox Corporation in the United States and/or other countries. Document Version: 1.0 (October 2012) BR3142...
-
Page 3: Table Of Contents
Stacker Unload Button .......................... 4-1 In Use Indicator ............................4-2 Attention Light ............................4-2 Jam Detection ......................5-1 Jam Clearance and Job Recovery ......................... 5-2 Location of the Baffles .......................... 5-3 Clearing Stray Sheets ..........................5-3 Troubleshooting ...................... 6-1 Xerox Production Stacker Operator Manual... - Page 4 Contents Xerox Production Stacker Operator Manual...
-
Page 5: Introduction
This document provides information for operating the Xerox Production Stacker (XPS). The XPS is an interface to the Xerox Nuvera system. It will enable inline finishing by receiving sheets from the host printer and sending these sheets into a stacker or other finishing device. -
Page 6: Safety Information
Warning: Hazardous moving parts. Keep fingers and other body parts away. This label is located on the front unload door. It warns you that the unload shutter doors move during the stack ejection. Xerox Production Stacker Operator Manual... -
Page 7: Warning Pictograms Location
Ready-to-Unload position. The light remains on steady while the Stacker Tray is in the unload position. Caution: Be careful moving around the stacker. The stack may be ejected at a low height waiting for an operator to remove the output. Xerox Production Stacker Operator Manual... -
Page 8: Methods To Stop The Motion Of The Stacker
When the Stacker Tray is ejecting and the Front Obstruction Bumper (shown below) comes into contact with an obstruction located in front of the ejector module, the ejection operation stops immediately. To restart, follow the instructions on the Xerox Nuvera Control Console. -
Page 9: Paper Process Description
Schematic View of the Paper Path Legend: 1. Input from upstream device 2. Top tray 3. Sheet path without stacking (with or without rotation) 4. Sheet path for stacking (without rotation) 5. Straight stack (no offset) 6. Offset stacking Xerox Production Stacker Operator Manual... -
Page 10: View Of Bypass And Rotation Path
Paper Process Description View of Bypass and Rotation Path Centered Input – Centered Output Without Rotation With Rotation Centered Input – Edge-registered Output Without Rotation With Rotation Xerox Production Stacker Operator Manual... -
Page 11: Machine Description
2. User interface 3. Top cover 4. Jam clearance door 5. Shutter doors 6. Docking plate to downstream device 7. Power cord. The power supply cord is used to disconnect the device. There is no main switch. Xerox Production Stacker Operator Manual... -
Page 12: Technical Specifications
Once open, the Stacker Tray moves out in front of the stacker. The Stacker Tray raises or lowers to a height that can be preset at the Xerox Nuvera Control Console. The attention light remains on continuously to signify that a stack is ready for pickup. -
Page 13: Retracting The Stacker
You can press the Stacker Unload button at any time to eject the stack (see Display Description). Optional settings for the Stacker Unload operation are available through the Xerox Nuvera Control Console. Refer to the Xerox Nuvera User Guide and Training Aid CD for more information on setting the following: •... - Page 14 Machine Description Xerox Production Stacker Operator Manual...
-
Page 15: Display Description
If there is only one stacker in a stacker group, printing pauses until the stack is ejected. Printing restarts when the stacker is clear. Refer to the Xerox Nuvera User Guide and Training Aid CD for Stacker Tray limits setup. -
Page 16: In Use Indicator
When the Attention light glows you can remove printed sheets. This gives a 360-degree view that the stacker is ready to unload. When the Attention light flashes, the external elevator is in motion (up/down or in/out). This gives a 360-degree view that the Stacker Tray is in motion. Xerox Production Stacker Operator Manual... -
Page 17: Jam Detection
The display represents the top tray and the paper path areas. When part of the mimic is illuminated, there is a problem in this area. When the top tray area of the display is highlighted, check the top tray area to clear the paper jam. Top tray Xerox Production Stacker Operator Manual... -
Page 18: Jam Clearance And Job Recovery
In case of a jam, the operator needs to clear the paper path from any jammed or damaged sheet. Note Always perform a jam clearance by first clearing sheets in devices located to the right of the finishing line. Then progressively clear the paper path moving towards the printer. Xerox Production Stacker Operator Manual... -
Page 19: Location Of The Baffles
In case stray sheets drop behind the Stacker Tray use the following process to clear the area. 2. Pause the Xerox Nuvera printer at the Control Console. 3. If the Stacker Tray is out and full, unload the stack. - Page 20 8. If necessary, you can lift the shutter door for easier access. 9. Once you have cleared all stray sheets, close the top cover. The stacker resets and moves to the ready position. 10. Release the print job at the Control Console. Xerox Production Stacker Operator Manual...
-
Page 21: Troubleshooting
Does not run when top wall outlet cover or door is closed. • Check if printer is ready • Check communication cable from Xerox Nuvera Product line printer to stacker for proper connection • Check for other area if the mimic not illuminated •... - Page 22 Troubleshooting Xerox Production Stacker Operator Manual...