Xerox DocuTech 180 Install Manual

Installation Preparation Document
The main DocuTech 180 HLC components are:
•
Digital Front End Controller
•
CD/DVD combo drive
•
color flat panel monitor
•
keyboard and mouse
•
Ethernet interface (10/100/1000 BaseT)
•
Two printer interface cards
•
Controller Stand
•
Options
•
USB floppy disk drive
•
Solaris 10 and DocuSP print services software
•
Printer
•
Black plus one highlight color*
•
Xerographic engine with laser raster imaging system for
black and Light Emitting Diode for color
•
Permanent housing for black dry ink; customer changeable
unit (CCU) for color dry ink
•
Prints simplex or duplex
•
Two-tray interposer
•
In-line finishing module which includes a binder, stitcher,
and stacker
•
Optional Bypass Transport to provide connection to
additional finishers
* Additional dry inks, not listed on this document, will be customer
options as they become available, and will be offered under standard
Xerox terms and conditions.
Space Requirements / Service Space Envelope
The dimensions shown below are absolute minimums.
Configuration Width
With two tray 78 (in)
Interposer and 198
Binder/Stitcher (cm)
Controller stand 36 (in)
91 (cm)
•
The minimum total space required includes the required space
necessary for the Xerox service personnel to service the printer.
•
A minimum of 78 inches/198 cm clearance from the floor to the
nearest overhead obstruction must be maintained.
•
No obstructions, such as power poles, are allowed such that
they interfere with the Xerox Service Representative's ability to
access the rear of the printer for service.
•
The printing system must be installed in a fixed location.
•
Space requirements for the controller stand are 36 x 36
inches/91 x 91 cm.
•
For proper operation, the printer must be perfectly level. On
floors less than two degrees out of level, a leveling kit must be
used to level the equipment. The printer will not function
properly on floors more than two degrees out of level.
•
For detailed space requirements and diagrams, refer to the
DocuTech 128/155/180 HighLight Color Installation Planning
Guide.
701P46151
October 2006
Xerox DocuTech 180 HighLight Color
Depth Min total Weight
req'd
Width x
depth
42 (in) 293.1 x 3724
106.6 142.0 (in) (lbs)
(cm) 744.5 x 1689
360.6 (kgs)
(cm)
36 (in)
91 (cm)
(for physical installation of the product only)
Electrical Requirements (printer)
The printer requires for 60 HZ service (2 cords required):
Voltage
Amperage (dedicated)
Cycles
Receptacle Xerox Part No.
Receptacle NEMA Part No.
Receptacle Diagram
Power Cord Kit Number
Power Cord Length
For 50 Hz service:
•
30 amp dedicated service (WYE): 220/380 VAC or 230/400
VAC or 240/415 VAC (3 phase)
Agency certifications: UL, cUL, CE Mark, FCC
Electrical Requirements (Controller)
The Controller requires 20 AMP dedicated service. The information
for the 20 Amp electrical service is identified below.
Line Options
Voltage
Amperage
Cycles
Xerox Receptacle Part No.
Receptacle NEMA Part No.
Power Cord Xerox Part No.
Receptacle Diagram
Installation Considerations
1. Dedicated electrical service is required for each component.
2. The controller can be connected to a 15 amp or 20 amp outlet.
3. The length of the cable from the controller to the printer is 16
feet (4.8 metres).
4. Do not use an adapter to connect the controller to an electrical
outlet that lacks a ground connection terminal.
5. The customer is responsible for providing the network and the
client workstation(s). The Ethernet interface on the DocuSP
controller is a auto-sensing 10/100/1000 - MB/sec twisted pair
standard (BaseT).
6. The Ethernet connection to the DocuSP controller must be
compatible with the Institute of Electrical and Electronics
Engineers (IEEE) 802.3 standard.
MultiSource
2-phase, dual power cord
configuration
208/240 208/240
(4 wire) (4 wire)
50 30
60 Hz 60 Hz
14-50R 14-30R
15 feet 15 feet
Controller 36 Track Tape
(Optional)
Dedicated Dedicated
115vac 115vac
20 20
60 Hz 60 Hz
600S3703 600S3703
5-20R 5-20R
98K19950 98K19950
97S02370 97S02370