Table of Contents
Advertisement
18. Installation of the water dispenser line
1) For automatic operation of the ice maker, water pressure of 1.4~4.5 kgf/ai is required.(It is
acceptable if the disposable paper cup(180cc) can be filled up with water within 10 second.)
2) The water tube can be used by cutting to the desired length. Make sure that the tube is not
bent.
3) Make the maximum length of the water tube to be 12m, if possible. If the length is over 12m,
it will cause a problem to supply water because of decrease of water pressure.
4) Locate the water tube at the area without heat.
5) The purifier is just for filtration. It will not work as sterilizer of microorganisms.
6) If the refrigerator is installed in the area with low water pressure(below 1.4 kef/at),
additionally purchased booster pump may be installed in order to compensate the shortage
of pressure.
7) The life cycle of purifier depends upon the condition of the usage, but we recommend that
you change it every 6 months. So we recommend that you install it at the place to access
easily for changing.
8) To supply water to the storage tank inside the refrigerator, press the cold water button for
about 2 or 3 minutes and make cold water drop from the cold water outlet.
9) In order to avid possible leakage, seal every joined area using sealing tape.
10) The water tube should be connecfed to the cold tap water.
# Check the components
Sealing Tape
(0203-00399)
A
Rubber packing
. .
iit
a
Wyn
<=,
Clip AX8EA
Screw-tapingX12EA
(DA65-20110B)
(6002-000213)
(DA73-10466F)
i
Tightening band
(6502-000156)
1. Connect coupler to the water tap.
The water tube should be connected
to the cold water pipe. If it is connected
to the hol water pipe, it may cause
some problems in the Functioning of
1) Close the main water tap.
2) Connect the coupler to the tap water.
3) Every joint should be taped with sealing
tape.(see the picture)
+ If the coupler doesn't fit to
the existing water tap, consult the
closest authorized service dealer and
purchase the right couplers for the
proper installation.
2. Connect the water tube to the conpler
Insert the waterfube into the conpler.
3. Select the purifier location for installation
1) Select the location of the purifier.
2) Cut water tube considering the
distances between Purifier and
waterworks tap, and Purifier and
water valve of Refrigerator
(At this time, it must be cut at a
reght angle.)
3) Insert water tubes of inlet side and
outlet side of Purifier.
A TUBE INLET SIDE TO PURIFIER
A TUBE INLET SIDE TO PURIFIER
4. Remove the residuals inside the purifies.
1) Open the main water valve to
check whether water is running
through the water tube from the
water inlet side of the purifier.
2) Leave the faucet open until clean
water is running out.
A OUTLET SIDE OF PUFIFIER
5. Fix the purifier lock station.
1) Hold the purifier lock station
against the lock hole of right-
lower side in the back of the
refrigerator and fix it tightly
using screw.
purifier lock station
purifier lock station
6. Fix the purifier.
1) Fix the purifier as shown int he
TER TL EES
picture on the right.
PURIFIER LOCK
STATION
7. Connect the water tube to the refrigerator.
1) Remove the back cover of
BACK COVEROF
CONNECT NUT
the refrigerator.
REFRIGERATOR
2) Connect the water tube to
—WATER TUBE
the valve as shown in
the picture.(The connector is
located at right side of the
machine room in the back of
the refrigerator.)
3) When connected, check
whether there is any leakage.
On leakage, reassemble them.
8. Put the water tube in order
1) Using the clip "A" and "B" fix
the water tube to the wall.
2) When the water tube is put in
order, make sure there are any
forced bending and pushing
against the water tube.
WATER TUBE
9. Complete the installation of the water dispenser line
1) Turn on the refrigerator and press
the left side lever until water is
coming out through the water
tube.(approximately 2~3minute)
(Press it until the initial air outing
phenomenon disappear.)
2) At this time, check any possible
leakage on the joints of the water
tube. After putting the water
tube in order, move the refrigerator
to the desired location. Once the
refrigerator is located, do not move
the refrigerator as possible.
Advertisement
Table of Contents
