Installation Of The Water Dispenser Line - Samsung SR-S25NTA Service Manual

18. Installation of the water dispenser line
1) For automatic operation of the ice maker, water pressure of 1.4~4.5 kef/al is required.(It is
acceptable if the disposable paper cup(177cc) can be filled up with water within a second.)
2) The water tube can be used by cutting to the desired length. Make sure that the tube is not
bent. ;
3) Make the maximum length of the water tube to be 12m, if possible. If the length is over 12m,
it will cause a problem to supply water because of decrease of water pressure.
4) Locate the water tube at the area without heat. -
5) The purifier is just for filtration. It will not work as sterilizer of microorganisms.
6) If the refrigerator is installed in the area with low water pressure(below 1.4 kef/ai),
additionally purchased booster pump may be installed in order to compensate the shortage
of pressure.
7) The life cycle of purifier depends upon the condition of the usage, but we recommend that
you change it every 6 months. So we recommend to install it at an eccess place for changing.
8) To supply water to the storage tank inside the refrigerator, press the cold water button for
about 2 or 3 minutes and make cold water drop from the cold water outlet.
9) In order to avid possible leakage, seal every joined area using sealing tape.
10) The water tube should be commected to the cold tap water. ,
-m Check the components
Coupler B
Nuts (DA73-10299D) Sealing Tape
w! (0203-00399)
? Coupler A
2 — (DA73-10299C)
Water valve
(DA73-90032A)
24
Rubber packing can ®)
Clip AXSEA
Screw-tapingX12EA (DA63-201108)
(6002-00213)
Se ely sf
(TID) et
ae
Purifier fl NS
i OY [a SE
.
ZEB
fi
~S ISN
Water Tube Purifier lock St ~
(DA29.10105B) WY
(DA73-10466F) station ~~ lip axsea
Tightening band (6502-000156)
PRECATUTION!
The water tube should be connected
to the cold water pipe. If it is connected
Pa to the hol water pipe, it may cause
1) Close the main water valve. some problems in the Functioning of
2) Connect the coupler "A" to the tap water the purcher.
valve.
3) Connect the coupler "A" and "B" to the
water pipe.
5) If there is only one water pipe, connect Ne oer
coupler "A" Ne COUPLER AG
HOT WATER -" <
— SN
Ps Ro
ESEPRENCE
1. Connect couplers and valve to the
water pipe.
s\)
2. Connect the water tube to water tube valve
1) Insert the nut into the water
tube ; WATER TUBE
2) Insert the water tube into the \
water tube valve as shown in
the picture on the right side.
3) Tighten the nut by turning it.
eo | A TUBE
COLDWATER WATER VALVE
3. Select the purifier location for installation
1) Cut the water tube, attached to
the purifier, to the proper length
after measuring the distance from
the location of the purifier to the
water tube valve.
2) If you want to reassemble the
water inlet side and outlet side of
the purifier during the installation
of the purifier, see the reference
picture.
A TUBE INLET SIDE TO PURIFIER
ATUBE INLET SIDETQ PURIFIER
4. Remove the residuals inside the purifies.
1) Open the main water valve to
check whether water is running HOT WATER
through the water tube from the »
water inlet side of the purifier.
2) If water doesn't come out through
the tube, turn the water tube COLD WATER
valve. PURIFIER WATER ATUBE WATER
3) Leave the faucet open until clean : Ko VAEYE
water is running out.
4) It is no problem with the residuals
because it might be left while
i
manufactruing the filter. A OUTLET SIDE OF PUFIFIER
5. Fix the purifier lock station.
1) Hold the purifier lock station
against the lock hole of right-
lower side in the back of the
refrigerator and fix it tightly
using screw.
=
>
7
purifier lock station
purifier lock station
oe 8 Y f
6. Fix the purifier.
1) Fix the purifier as shown int he WATER TUBE
picture on the right.
PURIFIER
TIGHT BAND
PURIFIER LOCK
STATION
7. Connect the water tube to the refrigerator.
BACK COVEROF CONNECT NUT
1) Remove the back cover of
REFRIGERATOR the refrigerator.
2) Connect the water tube to
the valve through the hole in
the back cover as shown in
the picture.(The connector is
lockated at right side of the
machine room in the back of
the refrigerator.)
3) When connected, check
whether there is any leakage.
On leakage, reassemble them.
WATER TUBE
8. Put the water tube in order
1) Using the clip "A" and "B" fix
the water tube to the wall.
2) When the waier tube is put in
order, make sure there are any
forced bending and pushing
against the water tube.
9. Complete the installation of the water dispenser line
1) Turn on the refrigerator and press
the left side lever until water is
coming out through the water
tube.(approximately 2~3minute)
(Press it until the initial air outing
phenomenon disappear.)
2) At this time, check anv possible
leakage on the joints of the water
tube. After putting the water
tube in order, move the refrigerator
to the desired location. Once the
refrigerator is located, do not move
the refrigerator as possible.