Table of Contents
Advertisement
Phase 1:
programming th e overhead keypad
1. Make sure your vehicle is wit hin operating
range of the remote contro lled garage
door opener.
2. Set the parking brake
q
A
in General in-
formation on page 88.
3 . Turn the ignition on . Do not start the en-
g ine!
4.
Press and hold the two outs ide Home-
Link® buttons
(D
and @ for approxi-
mately 20 seconds until indicator light @
¢fig . 101
begins to flash . Then release
both buttons. Do not ho ld the buttons for
longer than 30 seconds.
.,. This procedure only needs to be performed
once.
It erases the factory-set default codes
and does not have to be repeated to pro-
gram add it ional remote controls.
S. Press and hold the Home Link® button
(D,
®
or @ unt il t he indicato r ligh t @
starts flashing
slowly.
Release the bu t ton.
.,. The system will remain in programming
mode for 5 minutes . Co to the front of the
vehicle and proceed with phase 2.
Phase 2:
programmin g th e bumper mounted tran s
mitter
6.
Hold the
original remote control
at a dis-
tance between 0 - 6 in. (0- 15 cm) from the
bumper below the appropriate headlight
for your vehicle
c:!;>
fig. 102
(use the short-
est distance possib le).
7 . Aim the remote cont rol just be low the
driver side
head light.
8.
Press and hold the activation button on
the remote contro l.
.,. May be different in Canada. If so, press and
re-press (cycle) the act ivation button on your
remote control every two seconds.
9. The emergency flashers will flash
three
time s
(after about 15-60 seconds) when
the programm ing is successful. Release
the butto n on the remote control.
.,. To program more devices, repeat steps 4 to
9.
Homelink
®
89
10. Press and hold the tra ined Homelink ®
button and observe the indicator light @
q fig. 101 .
.,. If the ind icator light is solid/contin uous,
programm ing is complete and your device
should activate when you press and release
the t ra ined Homel ink® button .
.,. If the ind icator light blinks rapidly fo r 2 sec-
onds and is the n a solid/continuous
light,
p roceed with phase 3 to program a roll ing
code device.
Phase 3: rolling code programming
.,. A second pe rson on a ladder who can safely
reach the garage door opene r motor is rec-
ommended .
11. Locat e the "learn" button on the ga rage
doo r opener motor (refer to the operating
instructions for the opener, as t he loca-
tion of t his button may vary by man ufac -
turer).
12. Press and release the learn button on the
garage door opener motor .
.,. Not e:
once the button is pressed, there are
30 seconds
in wh ich to init iate the next
step.
13. On t he Homelink ® keypad inside t he vehi-
cle, firmly press and ho ld the Homel ink®
bu tton prev iously programmed in phases
1 and 2 for two seconds and release. Re-
peat this sequence
twice.
.,. Some vehicles may require the press/hold/
release sequence up to three times to com-
plete t he trai ning process .
.,. Homelink ® should now activate your rolling
code equipped device.
If the S m inute time lim it is exceeded, the
emergency flash ers will flash one time
to in-
dicate that the p rocess has been te rminated.
In this case, repeat steps 4 t hrough 9.
If the emergency flashers do not flash
three
times (after about lS-60 seconds), program-
ming was not successful. In this case, repeat
steps 4 through 9 .
Remote contro l units for garage door openers
in Canada are set to stop transmitting
radio
frequency sig nals afte r two seconds. This t ime
Ill-
Advertisement
Table of Contents
