Denon D-F10 Manual page 7

Disc tray
Load discs here.
> (play) button
Press this button to start playing the disc.
Even when the disc tray is open, the disc tray closes
and playback begins when this button is pressed.
When pressed in the standby mode, the power
automatically turns on and playback begins. {Auto on
function)
@ (stop) button
Press this button to stop playback.
POWER switch
Press this once to turn the CO player's power on, then
press again to set the CD player to the standby mode.
in the standby mode, "OFF" appears on the display.
OPEN/CLOSE button
Press this to open and close the disc tray.
When oressed once, the disc tray opens out, and
when pressed again, the disc tray closes. If a disc is
loaded, the totat number of tracks and total playing
time of the disc are displayed several seconds after
the disc tray is closed.
When pressed in the standby mode, the CD player's
power turns on.
Display
144 / €4 (automatic / manual search reverse) button
Use this to move to the beginning of a specific track.
When pressed during playback or in the pause mode,
the pickup moves backward a number of tracks equal
to the number of times the button is pressed.
D> / PPI (automatic / manual search forward) button
Use this to move to the beginning of a specific track.
When pressed during playback or in the pause mode,
the pickup moves forward a number of tracks equal
to the number of times the button is pressed.
@ The automatic search mode is set if the @ or @
button is released within 0.5 seconds, and the
manual search mode is set if the button is held for
over 0.5 seconds.
li(pause) button
Press this button to stop playback temporarily.
Press the play dutton to cancel the pause mode and
resume playback.
The following is displayed on the track number display:
@ When the disc's data cannot be read properly
*@ Inthe stop mode ................. Totai number of tracks
e Inthe play and program modes . . Track number
@ When the innermost or outermost section of the disc is reached during the
> (the play indicator)
manual search operation ............ CCor 3 lights when a disc is
The following is displayed on the time display :
@ When the disc's data cannot be read properly ... ca cs playing.and lh: (the
pause indicator)
lights when the
pause mode is set.
e Inthe stop mode «0...
@ Inthe play and pause modes
@ Inthe program mode ...........
.. Total playing time
Elapsed time for current track
Elapsed time of programmed tracks
Track number display Time display
This lights when the
RANDOM button is
pressed.
LIBew8 6.88.
"PROG" lights during program- This lights if there are more
med playback. than 20 tracks on the disc.
Music calendar
The numbers of the tracks on the disc are displayed here (up to track number 20). The
number for the corresponding track turns off after that track is played.
During programmed playback, the numbers of the programmed tracks are displayed (up
to track number 20).
All the numbers light if the disc's data cannot be read properly.
This lights
when in the
standby
mode.
During the editing operation, "EDIT" lights, "A" is displayed on the track
display, the remaining time on side A is displayed on the time display,
and the numbers of the tracks to be recorded on side A light on the music
calendar. When the SIDE A/B button is pressed, "B" appears on the track
number display and the remaining time for side B is displayed in the
same way.
This changes as follows each time the REPEAT button is pressed:
1st press: REPEAT 1 (single-track repeat) is displayed and the number of the track to be repeated on the music calendar
lights.
2nd press: REPEAT ALL (al!-track repeat) is displayed.
3rd press: REPEAT A- is displayed.
4th press: REPEAT A-B is displayed.
5th press: Nothing is displayed.
(Only REPEAT 1 and REPEAT ALL are displayed in the stop mode.}
q@)
m
=
mi
a
>
-
2)
m
©)
=a
2)
2