Time Code; Memory Stop Function - Panasonic NV-DS99EN Operating Instructions Manual

ENGLISH
mmmmm
SWilh «•
Mte 0 8l*&SAe«i*«?Slit - ^nm#t!Lb%«IH*iJ:
B*tti*IBIMUK««T£ 0 Sltbtf/^T > MA&&W& • nffg
#i±i^g^(ohoomoosoof] • {inn^am
■
mmffimmmi
•^iejRF^p«ug«jgs» •
*»)»
(->34) ntsen
f^bll(-»35) •
tetftffih*ffi«»T5iJl»^:
■ Time Code
Time Code signals are the data which indicates the time in
hours, minutes, seconds and frames (25 frames/sec). Having
this data included in the recording gives every single picture on
the tape its own address.
•The Time Code is automatically recorded as part of the sub
code with every recording you make.
•When you insert a new (previously unrecorded) cassette, the
Time Code automatically starts from zero. If you insert a
recorded cassette, the Time Code continues where the time
code of the last previous scene stopped. (In this case, the
zero indication [OhOOmOOsOOf] may appear after inserting the
cassette, but when the recording starts, the Time Code
records from the previous value.)
•You cannot reset the Time Code to zero.
• In playback modes other than the Normal Playback Mode,
the Time Code may not be displayed (or not be correct).
• Unless the Time Code is recorded continuously from the
beginning of the tape, precise editing may not be possible.
To ensure that the Time Code is recorded without
interruption, we recommend that you use the Camera Search
Function
(H 34)
or Blank Search Function
35)
before
starting to record a new scene.
(->82)
2
US [VCR FUNCTIONS] iSHsE (CAMERA FUNCTIONS]
±%m±
[DISPLAY SETUP] ft [DISPLAY] (H^)
JSS9M& [MEMORY] (SSI®) "
3 •
4
&m
j|$ [POWER] MBflSfiMtE (VCR](|ftfi£^#|) o
5 @jwi8*$?bo
ftessfcj?*1 sen? itmis
1 ttOmmtmttttfftta - «>
2
m
[VCR FUNCTIONS] £&«s£ [CAMERA FUNCTIONS]
±mm±
[DISPLAY SETUP] [DISPLAY] (Htk)
BftaMte [MEMORY]
(SB*)
»
3 -
mtmitmm
°
4 mating. (-»64)
■ Memory Stop Function
The Memory Stop Function is convenient for the following
operations.
Rewinding or fast-forwarding the tape to a desired
position
1 Reset the Tape Counter to zero at the tape
position from which you want to play back
later. (-*
82
)
2
Set [DISPLAY] on the [DISPLAY SETUP] Sub-
Menu of the [VCR FUNCTIONS] or the
[CAMERA FUNCTIONS] Main-Menu to
[MEMORY].
3
Start playback or recording.
4
After playback or recording is finished:
Set the [POWER] Switch to [VCR].
5
Rewind the tape.
The tape automatically stops approximately at the
position at which you reset the counter to zero.
Stopping the editing automatically in audio dubbing
1 Reset the Tape Counter to zero at the tape
position at which you want the editing to stop.
2
Set [DISPLAY] on the [DISPLAY SETUP] Sub-
Menu of the [VCR FUNCTIONS] or the
[CAMERA FUNCTIONS] Main-Menu to
[MEMORY].
3
Play back a still picture at the point at which
you want the audio dubbing to start.
4
Start the audio dubbing. (-» 64)
The audio dubbing automatically stops approximately at
the position at which you reset the counter to zero.