Alpine CDA-7832R Service Manual page 53

4. Operations at ACC OFF
At ACC OFF, if the system is executing the timing chart,
it completes the mode and then enters the standby
mode.
However, if a DISC IN (disc is not removed) status is
detected after completion of Eject, the system enters the
standby mode after performing the loading to protect the
disc. If a loading error occurs at that time, the system
does not shift to the eject mode but shifts after the ACC
ON.
Moreover, an OR operation is carried out for SW-A and
SW-B and the result is fed to an interruption port. If it is
"L'-+"H", the system returns from the standby mode and
carries out the loading operation.
After completion of the loading or determining the load-
ing error, the system enters the standby mode again.
4. ACC OFFRFOMUIE
ACC OFFRR, RTS UAF +—-—hRTPRCHNIL, F
MODE @ 5S Ff L TS STAND BY MODEIZA4,
(BL. EJECTH TRDISC IN HREMSN TUE) O
TRAD FR SN TUE 5. DISCHREEM 7: LOADING
% 47> TH SSTAND BY MODE!" AS. % MRELOAD-
ING ERROR#384 L cde Ste ldé. EJECT MODE (= LR
t$. ACCONtH2TBATSCEEFS,
EE. /N- FCSW-ACSW-BCORERY. BV iAA
PORTICAHGT 4S. ACC OFFRFICEJECT MODE TS
), HOB) iIAAPORTH "L" > "H" Ceo Eee
b&. STAND BY? 5 (ii LLOADINGSH(E & 17 3.
LOADINGSs fF & A ISLLOADING ERROREE. BE
STAND BY MODELL ASZ¢tETS.
5. Operations at ACC ON
At the ACC ON, previous mode is continued.
5. ACC ONE RUF
ACC ONB# lt a] MODE @ He TS CE ETS,
6. Return from eject error
When both SW-A and SW-B go "H"-+"L" in Eject error
mode, the system completes the eject operation by as-
suming the disc is removed.
6. EJECT ERRORS }) O48)%
EJECT ERROR MODER#(CSW-Ads £ USW-BM & BIC
"H+ "LU (eo RBS,
DISCHE AONE
SNE LTEJECTET ETS.
DP-L
SERIES
7. Emergency eject process
Eject key is not accepted in all modes. However, when
ejecting in a mode other than chucking status (C mode),
the system performs the loading operation once and
then ejects as in initialization. (To prevent disc from pop-
ping out.)
7. RBEJECTRE
FX TOMODEIC SU TEJECT KEYVIC BUI SHO
etd.
(AL. Fay ¥Y TIRAB (C MODE) Liste SEJECTS
SBS. FIV HII ABLCAMUEDIC. WoOKA
LOADING LUT#5EJECTTSENETFS, (DISC
OPRUYW LERCH)
8. BATT detection
When the BATT detection port detects BATT OFF, the
system enters the standby mode under any conditions.
After releasing the standby, the system checks status of
the switches and performs initialization process if the
status is other than the chucking status (C mode).
8. BATTARH
BATTHREIMPORTABATT OFF &4RFIL 75. RSE
(CSTAND BY MODEIZ AS.
STAND BYPRERIR OME E L TIS, SWOIRKE & HEB
L. Fry > TRA (C MODE) WUHOBSIClt. 7
LY 7t AMBETIONETS,
9. Timing allowance
Basically +10%.
9. BLS LIOREICIDWT
H10%ERALTS,
10. Elimination of switch chattering
Performs for 8 ms and 2 time coincidence.
10.SWOF vv B2UU AFR) MBC DUT
8ms CiTL\, 2E—-RMe TS,