Table of Contents
Advertisement
Programming The Universal Remote Control
VCR
Cable Converter
Box
Preferred
Procedure
- Code
Known
Programming
Universal
Remote
Using
Infra-Red
Access
Codes
for VCRs
• Determine brand of VCR.
• Identify code(s) associated
with the brand in the
infra-red
code
index
for VCRs
(located
in this
manual).
Procedure
1.
Place the Remote TV/CABLE switch into the TV
position (Left).
'rvlcABLE
r¢7
2.
3,
Press and hold VCR POWER button down on
Universal Remote.
VCR POWER
©
Enter two digit code using numeric keypad (0
through 9 buttons). Release VCR Power button.
The Universal Remote is now programmed.
Note: Some brands have multiple codes. Repeat
procedure using each code listed until VCR
responds correctly.
Alternate
Procedure
- Code
Unknown
Programming
Universal
Remote
Using
the
"Sequence
Method"
for VCRs
• Confirm VCR is plugged in and operating properly,
then turn OFF.
Procedure
1.
Place the Remote TV/CABLE switch into the TV
position (Left).
WK:A.UE
2.
Press and hold the VCR POWER button down on
Universal Remote.
V_ER
3.
Press VOL RIGHT button repeatedly. Check for the
VCR to turn ON after each press. When the VCR
turns ON, release VCR Power button. The proper
infra-red code has now been accessed.
Preferred
Procedure
- Code Known
Programming
Universal Remote Using Infrared
Access
Codes for Cable Television Converter
Boxes
• Determine brand of Cable Television Converter box.
• Identify
code(s)
associated
with the brand in the
infra-red
code index for Cable Television Converter
boxes (located in this manual).
Procedure
1.
Place the Remote TV/CABLE switch into the CABLE
position (Right).
_ICA,LE
F-m]
NOTES:
1.
It maytake several attempts before the correct code
is found.
2.
The VOL LEFT button can be used to return to a
code that was accidently passed by,
3.
Some Remote Controls may have unique operating
functions
for some buttons.
For Example:
The
POWER button may only turn the VCR OFF as
opposed
to both ON and OFF. It will then be
necessary to modify the procedure. Turn the VCR
ON and repeatedly press the VOL RIGHT button
until the VCR turns OFF.
2.
Press and hold the CABLE POWER button down on
Universal Remote.
CABLE
POWER
3.
Enter two digit code using numeric keypad (0 through 9
buttons).
Release
CABLE
Power
button.
The
Universal Remote is now programmed. Use the
Remote CHANNEL UP/DOWN buttons for selecting
Cable Converter Box channels.
Note: Some brands have multiple codes. Repeat
procedure using each code listed until Cable
Television Converter box responds correctly.
Alternate
Procedure
- Code Unknown
Programming
Universal
Remote
Using
the
"Sequence
Method"
for
Cable
Television
Converter
Boxes
• Confirm Cable Television Converter box is plugged in
and operating properly, then turn OFF.
Procedure
1.
Place the Remote TV/CABLE switch into the CABLE
position (Right).
W_CABL_
2.
Press and hold the CABLE POWER button down on
Universal Remote.
CABLE
POWER
3.
Press VOL RIGHT button repeatedly. Check for the
Cable Television Converter box to turn ON after each
press. When the Cable Television Converter box turns
ON, release Cable Power button. The proper infrared
code has now been accessed,
NOTES:
• It may take several attempts before the correct code is
found.
• The VOL LEFT button can be used to return to a code
that was accidently passed by.
• Some
Remote Controls may have unique operating
functions for some buttons. For Example: The POWER
button may only tum the Cable Television Converter box
OFF, as opposed to both ON and OFF. It will then be
necessary
to modify the procedure. Turn the Cable
Television Converter box ON, and repeatedly press the
VOL RIGHT button until the Cable Television Converter
box turns OFF.
NOTE: When operating equipment (VCR or Cable Converter box) with the Universal Remote Control, the TV/CABLE
Switch should be set to the same position where the Access Code was first programmed for the equipment.
Otherwise, leave the switch in the TV position.
- 25 -
Advertisement
Table of Contents
