Table of Contents
Advertisement
Table 7 — Electrical Data
FURNACE
eRe
VOL NOt RANGE
MAX. UNIT
AMPACITY
MAX. WIRE
MAX. FUSE OR
Wine
SIZE
PHASE
Max
Min:
AMPS
#
LENGTH — FT (M)t | CKT BKR AMPS Tf
GAUGE
070—12/036070
115-60-1
127
104
9.0
11.99
30 (9.0)
15
14
090—16/048090
115-60-1
127
104
9.6
12.56
29 (8.8)
15
14
110—20/060110
115-60-1
127
104
15.4
19.33
29 (8.8)
20
12
135 —22/066135
115-60-1
127
104
14.9
19.13
30 (9.0)
20
12
155—22/066155
115-60-1
127
104
15.0
19.23
29 (8.8)
20
12
* Permissible limits of the voltage range at which the unit operates satisfactorily.
# Unit ampacity = 125 percent of largest operating component's full load amps plus 100 percent of all other potential operating components'
(EAC, humidifier,
etc.) full load amps.
TTime—delay type is recommended.
Length shown is as measured
1 way along wire path between furnace and service panel for maximum
2 percent voltage drop.
4
WARNING
FIRE HAZARD
Failure to follow this warning could result in personal
injury, death, or property damage.
Do
not
connect
aluminum
wire
between
disconnect
switch and furnace. Use only copper wire.
Use a separate, fused branch electrical circuit with a properly
sized fuse or circuit breaker for this furnace. See Table 7 for wire
size
and
fuse
specifications.
A
readily
accessible
means
of
electrical disconnect must be located within sight of the furnace.
NOTE:
Proper polarity must be maintained for 115-v wiring. If
polarity is incorrect, control LED status indicator light will flash
rapidly and furnace will NOT operate.
J-Box Relocation
NOTE:
If factory location of J-Box is acceptable, go to next
section (ELECTRICAL CONNECTION to J-Box).
NOTE:
On
14-in. (356 mm) wide casing models, the J-Box
shall not be relocated to other side of furnace casing when the
vent pipe is routed within the casing.
1. Remove
and save two screws holding J-Box. (See Fig.
23.)
NOTE:
The J-Box cover need not be removed from the J-Box
in order to move
the J-Box.
Do
NOT
remove
green ground
screw inside J-Box.
(See Fig. 23.)
2, Cut wire tie on loop in furnace wires attached to J-Box.
3. Move J-Box to desired location.
4, Fasten J-Box to casing with the two screws removed in
Step 1.
5. Route J-Box wires within furnace away from sharp edges,
rotating parts and hot surfaces.
Electrical Connection to J-Box
Electrical Box on Furnace Casing Side (See Fig. 24.)
FIRE OR ELECTRICAL SHOCK HAZARD
Failure
to follow
this warning
could
result
in personal
injury, death, or property damage.
If field-supplied manual disconnect switch is to be mounted
on furnace casing side, select a location where a drill or
fastener cannot damage electrical or gas components.
_ Alternate
cation
A10204
Fig. 23 - Relocating J-Box
1. Select and remove a hole knockout in the casing where the
electrical box is to be installed.
NOTE:
Check that duct on side of furnace will not interfere with
installed electrical box.
2. Remove the desired electrical box hole knockout and posi-
tion the hole in the electrical box over the hole in the fur-
nace casing.
3. Fasten the electrical box to casing by driving two field-
supplied
screws
from
inside
electrical box
into casing
steel.
4. Remove
and save two screws holding J-Box. (See Fig.
23.)
5. Pull furnace power wires out of 1/2-in. (12 mm) diameter
hole in J-Box.
Do
not loosen wires from strain-relief
wire-tie on outside of J-Box.
6. Route furnace power wires through holes in casing and
electrical box and into electrical box.
7, Pull field power wires into electrical box.
8. Remove cover from furnace J-Box.
9, Route field ground wire through holes in electrical box
and casing, and into furnace J-Box.
10. Reattach furnace J-Box to furnace casing with screws re-
moved in Step 4.
11. Secure field ground wire to J-Box green ground screw.
12. Complete electrical box wiring and installation. Connect
line voltage leads as shown in Fig. 24. Use best practices
(NEC in U.S. for wire bushings, strain relief, etc.
13. Reinstall cover to J-Box.
Do
not pinch wires between
cover and bracket.
Advertisement
Table of Contents
