Table of Contents
Advertisement
I
I
I
I
HAZARD SYMBOLS
Someof the followingsymbols may be usedon thistool.Pleasestudy themand learntheir
meaning.Proper interpretation of these symbolswill allowyou to operatethe tool better and safer.
SYMBOL
NAME
DESIGNATION / EXPLANATION
Q
No Hands Symbol
Failure to keep your hands away from the blade will
result in serious personal injury.
Q
No Hands Symbol
Failure to keep your hands away from the blade will
result in serious personal injury.
Q
Eye Protection
Always wear safety goggles or safety glasses with side
shields and a full face shield when operating this product.
O
Hearing Protection
Always wear hearing protection when operating
this product.
Hand Protection
Always wear work gloves when operating
this product.
SAFETY PRECAUTIONS
FOR LASERS
This CRAFTSMAN
7-in. Tile Wet Saw has a built-in laser light. The laser is a
Class Ilia and emits output power of a maximum 2.5mW and 650nm wavelengths.
These lasers do not normally present an optical hazard.
However, DO NOT stare at the beam as this can cause
flash blindness.
CAUTION: The following label is on your tool. It indicates
where the laser light is emitted by the saw. ALWAYS
MAKE
SURE that any bystanders in the vicinity of use are made
aware of the dangers of looking directly into the laser.
AVOID
EXPOSURE-Laser
radiation
is
emitted
through
this
aperture
LASER
RADIATION
DO NOT
STARE
INTO
BEAM
_
650nm
Output:_2,SmW
Class
Ilia
Laser
Product
Complies
with
21CFR
parts
1040.10
and
1040.11
Made in China
Sears
Roebuck
and Co.
Model:
118.00000
/KWARNING:
LASER LIGHT. LASER RADIATION.
Avoid Direct Eye
Exposure.
DO NOT stare into beam. Only turn laser beam on when using
the tile saw.
_WARNING:Use
of controls, adjustments
or performance
of procedures
other than those specified in this manual may result in hazardous radiation
exposure.
AWARNING:
The use of optical instruments
such as, but not limited to,
telescopes
or transits to view the laser beam will increase eye hazard.
4
SAFETY PRECAUTIONS
FOR LASERS cont.
1. The laser beam system is mounted to the blade guard. Never remove from blade
guard to use on another tool or use for other purposes.
2. The laser beam can be harmful to the eyes. ALWAYS
avoid direct eye exposure.
DO NOT look directly into the laser beam output aperture during operation.
3. The laser on the tile saw is not a toy. ALWAYS
keep out of the reach of children.
The laser light emitted from this device SHOULD NEVER be directed towards
any person for any reason.
4. Be aware that laser light reflected off of a mirror or any other reflective surfaces
can also be dangerous.
WORK AREA SAFETY
1. Keep your work area clean and well lit. DO NOT leave tools or tile pieces on
on the saw while it is in operation. Cluttered work benches and dark areas
invite accidents.
2. DO NOT operate
power tools in explosive
atmospheres,
such as in the
presence of flammable
liquids,
gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep bystanders,
children
and visitors
away while operating
a power tool.
Distractions can cause you to lose control.
4. Make your workshop
childproof
with padlocks and master switches, or by
removing tab in the middle of starter switch (See Fig. 26 on page 16).
5. MAKE SURE the work area has ample lighting so you can see the work and
that there are no obstructions
that will interfere with safe operation BEFORE
using your saw.
PERSONAL
SAFETY
1. KNOW your power tool. Read the operator's manual carefully. Learn the saw's
applications
and limitations, as well as the specific potential hazards related to
this tool.
2. STAY ALERT, watch what you are doing and use common sense when operating
a power tool.
3. DO NOT use tool while tired or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power tools may result in
serious personal injury.
4. DRESS properly.
DO NOT wear loose clothing or jewelry. Pull back long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothing or
long hair can be caught in moving parts. Air vents often cover moving parts and
should also be avoided.
5. AVOID accidental starting. BE SURE switch
is in the "OFF"
position
before
plugging
in.
6. REMOVE adjusting keys or wrenches before turning the tool "ON". A wrench or
a key that is left attached to a rotating part of the tool may result in personal injury.
7. DO NOT overreach.
KEEP proper footing
and balance
at all times. Proper
footing and balance enables better control of the tool in unexpected situations.
8. USE SAFETY EQUIPMENT.
ALWAYS
wear eye protection.
Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
9. NEVER stand on tool. Serious injury could occur if the tool is tipped or if the
blade is accidentally contacted.
5
I
I
I
I
2-2-06
Advertisement
Table of Contents
