Baud Rate; Mounting The Keypanel And Accessories; Standard Connections; Gooseneck Microphone - RTS KP96 SERIES Installation Instructions Manual

•
ADAM CS with RJ-11 or DB-9 back panel: You
can determine the correct logical keypanel address
from the worksheet in either of two ways: 1) If you
know the port number that a keypanel will be
connected to, look up the port number in the
worksheet, then read across to the appropriate logical
keypanel number for that port number. 2) If you
know the connector number (on the back of the
ADAM CS frame) that the keypanel will be
connected to, look up that connector number in the
worksheet, then read across to the appropriate logical
keypanel number.
Once you have determined the correct logical
keypanel number, refer to Table
switches 4 through 7 to set this as the address.
•
ADAM CS frame with 50-pin Telco back panel:
You can determine the correct logical keypanel
address from the worksheet in either of two ways: 1)
If you know the port number that a keypanel will be
connected to, look up the port number in the
worksheet, then read across to the appropriate logical
keypanel number for that port number. 2) If you
know the connector numbers and pin numbers that
the keypanel will be connected to, look up these
numbers in the worksheet, then read across to the
appropriate logical keypanel number.
Once you have determined the correct logical
keypanel number, refer to Table
switches 4 through 7 to set this as the address.
ADAM Intercom Systems: To set the address, first refer
to Table 8, page 20, and locate the intercom port number
to which the keypanel will be connected. Then, read
across to the "Address" column to find the logical key-
panel address (it will always be a number between 1 and
8). Finally, refer to Table 1
this address number.
2.4.4

Baud Rate

SW1-8 selects the baud rate for communication with the
intercom system's configuration computer. For all
ADAM, ADAM CS, and Zeus intercom systems this
switch must be set to the open position (9600 baud). Do
not use the 76.8 kbaud setting.
10 Installation Instructions, KP96 / KP97 Series Keypanels
1 and position DIP
1 and position DIP
and set the DIP switches to
2.5 MOUNTING THE KEYPANEL AND
ACCESSORIES
Keypanels, expansion panels and level control panels may
be mounted in any industry standard 483 mm (19") wide
equipment rack or equipment bay. For all panels, allow an
additional 2 to 3 inches in back for cables and connectors.
No special tools other than those found in a typical tool
kit are required for mounting. The panels have no special
ventilation requirements.
For ease of use, when positioning the panels it may help
to locate each level control panel directly above or below
the keypanel or expansion panel that it will be used with.
Otherwise, you will have to label each LCP control knob
according to the key assignment alphas on the keypanel or
expansion panel.
2.6

STANDARD CONNECTIONS

2.6.1

Gooseneck Microphone

If you ordered the keypanel with a gooseneck micro-
phone, screw the microphone into the panel microphone
jack on the front panel.
2.6.2

Front Panel Headset

The front panel headset jack accepts a monaural,
dynamic-microphone headset. Headphone impedance
should be 8 to 400 ohms. Nominal microphone output
should be -60 dBm, 150 ohms.
Connector Type: D4F (Mates with A4M)
Pin 1: Microphone -
Pin 2: Microphone +
Pin 3: Headphone -
Pin 4: Headphone +
2.6.3

Connection To Intercom Matrix

Use either a 9-pin or RJ-11 intercom cable (but not both)
to connect to the intercom system. You can use a prefabri-
cated cable, or construct a cable using the wiring diagram
in Figure 4 or 5. Plug one end of the cable into the P10 or
P11 connector on the back panel of the keypanel. Plug the
other end into the appropriate port of the intercom system.
(This will be the port number that you designated previ-
ously when setting the address DIP switches.)
Keypanels may be connected while the intercom
system is running.