RTS KP95 Installation Instructions Manual
Adam, adam cs, and zeus intercom systems
Hide thumbs
Also See for KP95:
- Operating instructions manual (8 pages) ,
- Parts manual (43 pages) ,
- Operation manual (15 pages)
Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
ADAM™, ADAM™ CS, AND ZEUS™ INTERCOM SYSTEMS
Talk
Off
(Talk)
BY
Matrix Intercom System
Talk
Off
(Talk)
BY
Matrix Intercom System
9330-7101-004 V8.2 Rev A 12/97
KP95-0 KEYPANEL
VERSION 8.2
WITH EKPD-95 EXPANSION PANEL
Talk
KP95-0 Keypanel
Talk
EKPD-95 Expansion Panel
Clear
Off
Call
Answer
Incoming Messages
Programing
™
Advertisement
Table of Contents
Related Manuals for RTS KP95
Summary of Contents for RTS KP95
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS ADAM™, ADAM™ CS, AND ZEUS™ INTERCOM SYSTEMS Talk (Talk) Matrix Intercom System Talk (Talk) Matrix Intercom System 9330-7101-004 V8.2 Rev A 12/97 KP95-0 KEYPANEL VERSION 8.2 WITH EKPD-95 EXPANSION PANEL Talk KP95-0 Keypanel Talk EKPD-95 Expansion Panel Clear Call... -
Page 2: Proprietary Notice
The sole obligation of Telex during the warranty period is to pro- vide, without charge, parts and labor necessary to remedy covered defects appearing in products returned prepaid to Telex. - Page 3 Installation Instructions, KP95-0 Keypanel 3...
- Page 4 This page intentionally left blank. 4 Installation Instructions, KP95-0 Keypanel...
-
Page 5: Table Of Contents
MICROPHONE PREAMPLIFIER ..........TABLE OF CONTENTS Installation Instructions, KP95-0 Keypanel 5... - Page 6 Figure 1. KP95-0 Keypanel Reference View · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·...
-
Page 7: Introduction
INTRODUCTION This manual describes the installation of the KP95-0 Key- panel and EKPD-95 Expansion Panel. The manual is based on version 8.2 of the keypanel firmware. For oper- ating information, refer to the KP95-0 Operating Instruc- tion Manual, version 8.2. -
Page 8: Installation
However, if you wish to review these settings prior to installation, re- fer to “Electrical Adjustments”, page 12. 8 Installation Instructions, KP95-0 Keypanel DIP SWITCH SETTINGS The DIP switches are located on the back of the keypanel. -
Page 9: Baud Rate
If you previously configured the keypanel using the inter- com system configuration software, it should be ready for operation. Refer the station operator to the Keypanel Op- eration instructions in the KP95-0 Operating Instruction Manual. If the keypanel has not yet been configured you can do so now. -
Page 10: Printing Designation Strips
Ground system, the keypanel should be ready for operation. Refer the station operator to the Keypanel Operation instruc- tions in the KP95-0 Operating Instruction Manual. PRINTING DESIGNATION STRIPS Designation strips can be printed for configured keypanels by using the ADAMedit or ZEUSedit software. You can... -
Page 11: Terminal Block Connections
2.9.4 An external microphone can be connected. The external microphone may be used with or without a front panel gooseneck microphone of the same type. (Internal key- Installation Instructions, KP95-0 Keypanel 11 EKPD-95 DRIVER EXTERNAL DRIVER DEVICE CIRCUIT... -
Page 12: Ext Line In Connector
Assign a talk key to a crosspoint using the configuration software, and place calls to and from the keypanel. 12 Installation Instructions, KP95-0 Keypanel The following symptoms may occur if the logical key- panel number is incorrectly set: 1) when a key is pressed... -
Page 13: J201 (External Input Muting)
(1KHz at 150 ohms) into the microphone connector. Or use the EXT MIC IN connector with the front panel microphone removed (ref Table 7, page for pin-out). 3. Activate the microphone by setting a Talk key to the latched-up position. Installation Instructions, KP95-0 Keypanel 13... -
Page 14: Figure 7. Locations Of Internal Jumpers And Trimmers
J202 Q402 J401 J403 J404 J406 Figure 7. Locations of internal jumpers and trimmers 14 Installation Instructions, KP95-0 Keypanel... - Page 15 4. Insert a common mode signal into the dynamic mic input of the HEADSET connector. 5. Adjust RV404 (internal) for a minimum common mode signal at the MIC PRE OUT connector. 6. Remove the signal at the dynamic mic input. Installation Instructions, KP95-0 Keypanel 15...
- Page 16 Terminate the + AMP OUT and - AMP OUT terminals with an 8-ohm, 10-watt resistive load. Connect an audio analyzer across the load. 16 Installation Instructions, KP95-0 Keypanel 3. Remove the keypanel audio connection from the intercom matrix. 4. Insert a +8dBu (1 KHz) signal into the audio input + and - pins of the FRAME connector, P10 (Table 2, page 10).
- Page 17 8-ohm load at the headphone output of the HEADSET connector. 4. Adjust the SIDETONE trimmer (RV209) to 35 dB below a 2V AC reference level. (The level may be varied according to user preference.) 5. Remove the test equipment. Installation Instructions, KP95-0 Keypanel 17...
-
Page 18: Table 8. Correspondence Between Address Numbers And Intercom Port Numbers For Adam Intercom Systems
807 815 823 831 839 847 855 863 871 879 887 895 903 911 919 927 935 943 951 959 967 975 983 991 999 808 816 824 832 840 848 856 864 872 880 888 896 904 912 920 928 936 944 952 960 968 976 984 992 1000 18 Installation Instructions, KP95-0 Keypanel Intercom Port Numbers (8 Ports per Audio I/O Card) - Page 19 NOTES Installation Instructions, KP95-0 Keypanel 19...
- Page 20 ™...