TRENDnet User’s Guide TV‐IP315PI Specifications Product Overview 4 Megapixel Record up to 4MP HD video (2560 x 1440) at 30 fps in the space saving H.265 compression format. Covert Night Vision Masked IR LEDs provide covert night‐time viewing up to 30 meters (98 ft.) away. Smart IR Smart IR dynamically adjusts the Infrared (IR) LEDs by lowering the IR intensity when objects are near, and increasing IR intensity when objects are farther away Features PoE TRENDnet’s Indoor/Outdoor 4MP H.265 WDR PoE IR Dome Network Camera, Save installation costs with Power over Ethernet (PoE) model TV‐IP315PI, provides day and night surveillance with a night vision ...
Page 5
TRENDnet User’s Guide TV‐IP315PI Storage ONVIF Record video to a network storage device or to a Micro SD card (up to 128GB ONVIF Profile S and Profile G not included). Complimentary Apps Advanced Playback ® ™ Live video to a mobile device with free iOS and Android apps Advanced in‐camera archived video playback functionality Package Contents Motion Detection TV‐IP315PI package includes: Create custom motion detection zones to record video and send email TV‐IP315PI notifications when a zone is triggered. Weather seal ...
Page 6
TRENDnet User’s Guide TV‐IP315PI Front View Angle Adjustment Loosen the tilt lock screws, adjust the tilting position in a range, and tighten the tilt lock screws. Reset Button Push and hold the reset button then power on the camera. Keep holding the reset button for more than 10 seconds to reset configuration to factory 1. Mounting base default. 2. Horizontal stand 3. Vertical stand 4. Lower dome 5. 10/100Mbps PoE network port 6. Power port (optional) 7. Infra‐red lamps 8. Lens ...
Page 7
TRENDnet User’s Guide TV‐IP315PI Warnings Cautions Injury or equipment damage may be caused if any of these cautions are Serious injury or death may be caused if any of these warnings are neglected. neglected. Follow these precautions to prevent potential injury or material Follow these safety guards to prevent serious injury or death. damage. • If using the power adapter, please choose the power adapter that meets the safety extra low voltage (SELV) standard or IEC60950‐1 and • Make sure the power supply voltage is correct before using the Camera. Limited Power Source standard. • Do not drop the camera or subject to physical shock. ...
Page 8
TRENDnet User’s Guide TV‐IP315PI • Sunlight: Avoid direct sun light exposure. Direct sun light will damage Plan for installation location the image sensor. If sunlight is necessary for your viewing purposes, provide protection for the image sensor. Viewing angle • Lighting: Consider installing your camera faces the same direction of The TV‐IP315PI is a dome camera with a focused viewing angle (81) that the light sources. Shooting images with top‐down position outdoor or provides non‐distorted and detailed images. Choose the location where has next to the existing light source are good choices. Avoid the light source good angle to shoot the image you expect to see. The motion detection area if it creates a shade that darkens the viewing area. should also be considered when installing the camera. ...
Page 9
TRENDnet User’s Guide TV‐IP315PI Hardware Installation Setup Your Camera with Camera Utility 1. Please download the utility at Cabling http://www.trendnet.com/camerautility It’s recommended that the wiring the cable in your home or office by a professional. If you already have the cable deployed, make sure the cable and 2. Extract the downloaded file and double click on the camera utility file the connectors meet the category 5 Ethernet cable standards. At least 2 pairs to install of twisted lines are required for power and data. Poor cable quality may cause unexpected problems. Testing your cable or running a new cable is suggested for new camera installation. Waterproof cap The TV‐IP315PI itself is IP66 grade water and dust proof. There is a set of ...
Page 11
TRENDnet User’s Guide TV‐IP315PI Logging‐in to the Camera for the First Time (Windows) 3. The camera management page will detect if you installed the camera video streaming plug‐in or not. . Click the link to download the plug‐in 1. Find the camera from the Utility and double click on the IP address to from the camera. (For Internet Explorer and Safari only) Google and open the browser. Firefox users, skip to step 9. 2. Activate the admin User Account by entering your desired password, and ...
Page 13
TRENDnet User’s Guide TV‐IP315PI 9. Refresh the browser and the Live View page will show up and begin Logging‐in to the Camera for the First Time (OS X) streaming video 1. Open the web browser on your computer. In the address bar, enter the default IP address of the camera 192.168.10.30. If the camera is connected to a router/network, please use a windows machine to setup the camera with Camera Utility. 2. ...
Page 14
TRENDnet User’s Guide TV‐IP315PI 4. The camera management page will detect if you installed the camera 6. Go to the Finder and navigate to the Download folder. Command‐Click webcomponent plug‐in or not. Click the link to download the plug‐in from the WebComponents.pkg and then click Open. (If you are install the plug‐ the camera. in from the CD when you don’t have internet connection, just browse to /Mac folder and double click the WebComponents.pkg file.) Note: Internet connection is required to download the plug‐in. If you do not have Internet access, you can find the plug‐in on the CD comes with the package under /Mac folder. 7. Click Open with Installer to start installation. 5. Quit your browser completely by command‐Click on the browser icon ...
Page 17
TRENDnet User’s Guide TV‐IP315PI Live View After you log‐in into the camera management page, you’ll see the Live View page. Snapshot Click this icon to take a video snapshot. Zoom Click once to enable zoom. When enabled, click and drag the area on the picture to zoom in. Right click to resume 100% zoom. Click the icon again to disable zoom. The zoom function works in full screen mode as ...
Page 18
TRENDnet User’s Guide TV‐IP315PI Playback Time Line There is a play back head in the center of the time line represented in a yellow You can playback the video recording on the network storage and download vertical line. To look for a specific video recording, move the time line by the video clip and snapshots to your local computer. clicking and dragging it. If the recording is short, zoom in by clicking button. Click to zoom out the time scale. If you know the exact time of ...
Page 19
TRENDnet User’s Guide TV‐IP315PI Playback Slice images from video playback Use playback controls to play back the video recording. You can take snapshots from playback video or make new video clips from the video you are playing back. Click this button to play the video. Click this button to enable zoom. Then click and drag on Click this button to pause video playback. the video to define the area you want to zoom in. Click Click this button to stop playback. again to get back to 100% zoom. Click this button increase playback speed*. Double click to show video in full screen and press ESC Click this button decrease playback speed*. on keyboard to exit full screen mode. Click to playback video frame by frame. Click again for Click this button to disable zoom. ...
Page 20
TRENDnet User’s Guide TV‐IP315PI Download sections of video Download snapshots To save complete video sections or snapshots, you can download the files directly. Click button to list snapshots to download Click button to download video sections. Check the time of the recording, select the videos you want to download, and Select the type of event that triggered the snapshots. then click Download. Choose the Start Time and End Time. Then, click Search ...
TRENDnet User’s Guide TV‐IP315PI System Configuration Authentication RTSP: TV‐IP315PI’s video stream can be accessed with RTSP, Real Time Streaming Protocol. Only the Device Settings administrator and users can view this video stream Un‐checking this box will allow everyone access to this video Setup your camera name and location for easy identification. This camera stream without authentication. Default: Checked. name will also be recognized by other network camera software as the name of this camera. OSD, On Screen Display, camera name is referring to this setting as well. Service ...
TRENDnet User’s Guide TV‐IP315PI User Accounts Time Settings You can setup up to 16 user accounts to access the camera’s video stream The accuracy of the system clock is important for scheduling and accurate with a web browser or real time video stream (RTSP). Only one administrator logging. You can synchronize the system time with your computer, or account can be setup to configure the TV‐IP315PI and cannot be deleted. automatically check the time accuracy with a network time server (NTP ...
TRENDnet User’s Guide TV‐IP315PI Daylight Savings Live View Settings Setup daylight savings. Setup the live view video quality, file size and file saving directories. Automatic Update Enable DST: Check this box if your time zone has daylight savings. Start Time: Enter the date that daylight savings starts End Time: Enter the date that daylight savings ends DST Bias Enter how much time the daylight saving adjusted by daylight savings. Live View Parameters Click Save to save the changes Live View Configure the buffer size for live view video stream. With Buffer: low buffer size setting, you can get real‐time video ...
TRENDnet User’s Guide TV‐IP315PI Maintenance Record File Settings Record file size: This size of live view video recording. You can choose 256MB, 512MB, or 1GB a file. Smaller file size is good You can restart, load camera settings and upgrade the camera firmware on for many short recordings. this page. Save record Click Browse and then choose a new destination if you files to: want to save the file somewhere else. Save Click Browse and then choose a new destination if you downloaded want to save the file somewhere else. files to: Picture and Clip Settings Save snapshots Click Browse and then choose a new destination if you in want to save the file somewhere else. live view to: Save snapshots Click Browse and then choose a new destination if you when playback want to save the file somewhere else. to: Save clips to: Click Browse and then choose a new destination if you want to save the file somewhere else. Click Save to save the changes ...
Upgrade. Status: Shows the status in firmware upgrade. TRENDnet may periodically release firmware upgrades that might add features or fix problems associated with your camera. To find out if there is a firmware upgrade available for your device, please check your TRENDnet model and version using the link. http://www.trendnet.com/downloads/ 1. If a firmware upgrade is available, download the firmware to your computer. 2. Unzip the file to a folder on your computer. ...
Page 28
TRENDnet User’s Guide TV‐IP315PI Port Network Interface MAC Address: Click this button to reboot this camera. You can change the service port numbers of TV‐IP315PI and enable/disable Duplex and Choose one of the Ethernet duplex and speed to RTSP or HTTPS services. Speed: match your network. Default: auto. MTU: Maximum transmission unit. The maximum field size in the Ethernet packet. Multicast: Sends a stream to the multicast group address and allows multiple clients to acquire the stream at the ...
Page 29
TRENDnet User’s Guide TV‐IP315PI DDNS PPPoE Dynamic Domain Name Service, DDNS, allows you to find your camera from Setup PPPoE (ADSL) connection to connect your camera with your ISP, the Internet with an easy to remember domain name. Internet Service Provider. DDNS PPPoE (ADSL) Enable DDNS: Check this box to enable DDNS Service. Enable PPPoE: Check this box to enable PPPoE connection. DDNS Type: Select a DDNS service provider. Dynamic IP: The IP address assigned by ISP User Name: Enter the account name. Password: Enter the password. Confirm: Enter the password again. Server Address: Enter the DDNS server address. ...
TRENDnet User’s Guide TV‐IP315PI SNMP SNMP V1/V2 Enable SNMPv1: Check this box to enable SNMP v1 management. SNMP Settings allows you to assign the contact details, location, community Enable SNMPv2c: Check this box to enable SNMP v2c management. name and trap settings of SNMP. This is a networking management protocol Read SNMP Specify the password to access the SNMP Community: community for read only access. used to monitor network‐attached devices. SNMP allows messages (called Write SNMP Specify the password for access to the SNMP protocol data units) to be sent to various parts of a network. Upon receiving Community: community with read/write access. these messages, SNMP compatible devices (called agents) return data stored Trap Address: Specify the IP address for the SNMP trap in their Management Information Bases. community. Trap Port: Specify the port number for the SNMP trap community. Trap Community: Specify the name of SNMP trap community. ...
Page 31
TRENDnet User’s Guide TV‐IP315PI 802.1X Setup 802.1X for remote authentication service. Authentication Choose the authentication method to verify the Algorithm: source of information: MD5 or SHA. Authentication Specify the authentication password between 8 to 32 Password: letters. Private‐key Choose the privacy key to encrypt SNMP messages: Algorithm: DES or AES. Private‐key Specify the privacy key between 8 to 32 letters. Password: SNMP Other Settings SNMP Port: SNMP service port number. Click Save to save the changes 802.1X Authentication Enable IEEE Check this box to enable 802.1X authentication ...
TRENDnet User’s Guide TV‐IP315PI IP Address Filter Quality of Service (QoS) Set up a list of clients allow only the clients on the list to access this camera Setup traffic prioritization tags the video packets to go through network or to reject clients on the list from access this camera. switches and routers with assigned priority. You can set the Differentiated Services Code Point (DSCP) bits on outgoing data streams. The QoS capable network device will forward different data in different priorities. The meaning of the value is different in different DiffServ domains. Consult your network manager for the setup details. IP Address Filter Enable IP Check this box to enable IP address filtering service. Address Filter: IP Address Filter Choose Forbidden to ban the listed IP addresses or Type: Allowed to allow listed host to access this camera. Add: Click Add to add a user account Modify: To modify an entry on the list, highlight the entry by IP Address Filter clicking on it. Then, click the Modify button. ...
Page 33
TRENDnet User’s Guide TV‐IP315PI UPnP Video Settings Universal Plug‐and‐Play is a device discovery protocol set. It allows your Video Format camera to easily be found, for example, on a Windows operation system. UPnP Enable UPnP: Check this box to enable UPnP connection. Friendly Name: The name that will be appeared when searched. Port Mapping Enable Port Check this box to enable UPnP connection. Mapping: Port Mapping Choose Manual or Auto port mapping. Mode: External Port: Choose the port number for mapping. Click Save to save the changes ...
Page 34
TRENDnet User’s Guide TV‐IP315PI Resolution: H.264/H.265 MJPEG Bitrate Type: Choose between variable bit rate or constant bit rate for video compression. The default is variable rate. Video Quality: Choose the video quality. The default is medium quality. Frame Rate: Choose the capturing frame rate. The default value is 30 frames per second. Reduce the frame rate to reduce the capture file size. Max. Bitrate: Choose the maximum video sampling bit rate. Default: 2048 I Frame Interval An I Frame is a frame that records a complete picture. Frames between I frames, (P frame or B frame) only records the image differences between two frames. Choose the I Frame Interval here. The default is 60. Click Save to save the changes Sub stream can be used for lower resolution needed application, for example mobile app streaming or NVR streaming. Third stream is used for Live view only, it has resolution limitation on Chrome, Firefox and Safari. Max resolution can be supported under Internet Explorer. Note: When H.264+/H.265+ is enabled, Live view on Chrome or Firefox will be disabled due to browser limitation, you can continue to use Internet ...
Page 36
TRENDnet User’s Guide TV‐IP315PI Light sensitivities Schedule: Use quick selection or enter the time down below. Smart IR: Smart IR can adjust the strength of infrared lights at Click OK to confirm the time you want to set. night depending on the distance of an object to maintain the maximum IR light distance and while maintaining a clear picture when object is close by. Default: On. Max. Exposure Adjust this value for exposure time for Time: each picture. You can choose a value between 1/3 second to 1/100,000 second. The default value is 1/30 second exposure time for each picture. Start Time: The start time for day mode. Stop Time: The start time for day mode. Video Standard: This is the base frequency for the video refresh rate. It is recommended to set to the same frequency of your Position adjustments local video standard (NTSC: 60, PAL: 50). Default: Mirror: 60Hz. Day/Night Choose whether you want the Switch: camera to be set to the day mode Choose horizontal, vertical or both to adapt to the (color video) or night mode (IR physical position of installation. ...
TRENDnet User’s Guide TV‐IP315PI On Screen Display Settings Image adjustments Back Light Back light compensation: Setup a fixed light source Display the camera name and the time the video is shooting on the screen Compensation position to compensate and adjust the image in the and dark. Wide‐Dynamic‐ Choose the area that you want to enhance (dark area, Range: not light source). Note: By default, the WDR is disabled. Please enable WDR to set up back light compensation. WDR: Wide Dynamic Range compensates for the dark area dynamically. WDR Level: The level of compensation. Range: 0‐ 100%, default: 20%. White Balance: ...
TRENDnet User’s Guide TV‐IP315PI Text Overlay Privacy Mask Display extra information on the screen over the image. Create a masking area to keep your privacy. You can create up to four independent masking areas by clicking and dragging on the screen. Check Box: Check this box to enable text overlay. Text Field: Enter the text you want to display. You can enter your Enable Privacy Mask: Check this box to enable privacy masking. local language if you want. The text field allows Stop Drawing: Click this button to stop drawing. ...
TRENDnet User’s Guide TV‐IP315PI Video Recording Edit: Click Edit to edit the recording schedule. The Edit Schedule window will pop up. 1. Select day of the week you want to edit. 2. Select All Day or Customized schedule of the day. Pre‐record: Recording time before trigger event. 3. Set the time period and the event you Post‐record: Recording time after trigger event. want to trigger the video recording Overwrite: Select Yes to allow older recordings to be continuous (always recording) or motion overwritten. detection. Enable Record Check this box and then click Save to enable video 4. Click Select All or the weekday you want Schedule: recording. to have the same schedule on different day. Click Save to save the changes 5. Click another day of the week by clicking ...
TRENDnet User’s Guide TV‐IP315PI Events Motion Detection Set up how the motion detection event will be triggered and what actions will be triggered. Enable Check this box to enable motion detection. Click Save Motion to save the choice. Detection: Enable Check this box to enable motion tracking. Motion Motion tracking is a dynamic display that shows the current Tracking: status of motion detection. The motion tracking is ...
Page 41
TRENDnet User’s Guide TV‐IP315PI Draw Area: Click Draw Area button to start drawing. Click and 3. Set the time period and the event you want drag on the area you want to set up the motion to trigger the video recording continuous detection. You can draw up to 8 different areas. Click (always recording) or motion detection. Stop Drawing to stop drawing motion detection 4. Click Select All or the weekday you want to areas. have the same schedule on different day. ...
TRENDnet User’s Guide TV‐IP315PI Notification Arming Schedule Edit: Click Edit to edit the recording schedule. The Edit Schedule window will pop up. Provide notifications for other system events, set up your notifications here. 1. Select day of the week you want to edit. 2. Select All Day or Customized schedule of the day. 3. Set the time period and the event you want to trigger the video recording continuous (always recording) or motion detection. Notification 4. Click Select All or the weekday you want to Notification First, choose the exception type, and then choose have the same schedule on different day. Type: the corresponding action. 5. Click another day of the week by clicking on Send Email: Check this box to send an e‐mail notification when ...
TRENDnet User’s Guide TV‐IP315PI Snapshot Event triggered Enable: Check this box to take snapshots when an event is occurred. You can set up your camera to continuously taking snapshots or taking Format: Save snapshots in JPEG format snapshots only when events happening. Resolution: Uses the same resolution set in Video Format for the snapshot resolution. Quality: Choose a compression quality for snapshot. Interval: State the time interval between this series of ...
TRENDnet User’s Guide TV‐IP315PI Email address as your incoming email server, maybe not. Please ask your email service provider for detail. SMTP Port: Service port number for outgoing email.* Set up email accounts for notifications. Enable SSL: Check this box if your service provider requires a SSL secured connection. Attach Check Attach Image if you want to send a snapshot Image/Interval: image with the email notification and select the interval of snapshots in seconds. Authentication: Check this box if your server requires a password in order to send email. Most email servers require authentication when sending an email. User name: Enter the user name of outgoing email account Password: Enter the password Confirm: Enter the password again to confirm that the ...
TRENDnet User’s Guide TV‐IP315PI Network Storage No: The sequential number of the network storage. Network Storage Type: The type of storage. Server Enter the IP address of your network storage. Address: Network Storage must be setup before it can be managed. For storage File Path: Enter the shared folder as file path for network storage. You management, please refer to the next section. can create a folder under the shared folder and make it a ...
TRENDnet User’s Guide TV‐IP315PI Storage Management Format: Select a network storage volume and then click Format to format your network storage. This action will format the network volume (shared folder) for video recording. Network Storage must be setup before it can be managed. To setup storage, Placeholder files (formatting files) will be created to make ...
TRENDnet User’s Guide TV‐IP315PI FTP Server Enable Snapshot Check this box if you want to store snapshots on the to FTP: FTP. Server Address: Enter the FTP server IP address. Port: Enter the service port number of the FTP server. User Check Anonymous if the FTP server does not require Name/Anonymous authentication. Enter the User Name if the FTP server requires authentication. Password: Enter the password of the FTP account. Confirm: Enter the password again to make sure the password was entered correctly. Directory When saving snapshots on an FTP server, they can Structure: be saved in a single place or organized with meaningful directory names. Save in root directory: You can choose to store all files in the same folder of FTP login. Save in directory: Structure your folders with camera name or IP address. Directory: Use Camera Name: Use the camera name to organize the saved files. Use Camera IP: Use the camera IP address to ...
TRENDnet User’s Guide TV‐IP315PI FCC Caution: Any changes or modifications not expressly approved by the Appendix party responsible for compliance could void the user’s authority to operate this equipment. Direct video access ‐ RTSP This device complies with Part 15 of the FCC Rules. Operation is subject to the To access the video directly through RTSP, just visit the camera IP address on following two conditions: (1) This device may not cause harmful interference, port 554 by default. For example: 192.168.10.30:554 use the admin or user and (2) this device must accept any interference received, including password the login. interference that may cause undesired operation. Regulations Federal Communication Commission Interference Statement IMPORTANT NOTE: This equipment has been tested and found to comply with the limits for a ...
TRENDnet User’s Guide TV‐IP315PI Europe – EU Declaration of Conformity Français [French] Par la présente TRENDnet déclare que l'appareil TV‐IP315PI est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2004/108/CE, 2006/95/CE et. This device complies with the essential requirements of the Directive Italiano[Italian] Con la presente TRENDnet dichiara che questo TV‐IP315PI è conforme ai requisiti essenziali ed alle altre disposizioni 2004/108/EC and 2006/95/EC. The following test methods have been applied pertinenti stabilite dalla direttiva 2004/108/CE e 2006/95/CE. in order to prove presumption of conformity with the essential requirements Latviski [Latvian] AršoTRENDnetdeklarē, ka TV‐IP315PI atbilstDirektīvas of the Directive 2004/108/EC and 2006/95/EC: 2004/108/EK un 2006/95/EK būtiskajāmprasībām un citiemar to saistītajiemnoteikumiem. Safety /EMC Lietuvių Šiuo TRENDnet deklaruoja, kad šis TV‐IP315PI atitinka esminius EN 60950‐1: 2006 + A11: 2010 + A12: 2011 + A2: 2013 [Lithuanian] reikalavimus ir kitas 2004/108/EB ir 2006/95/EB Direktyvos EN 55024: 2010 + A1: 2015 nuostatas. ...
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO products that are replaced become the property of TRENDnet. Replacement products EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN may be new or reconditioned. TRENDnet does not issue refunds or credit. Please CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, contact the point‐of purchase for their return policies. INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE TRENDnet shall not be responsible for any software, firmware, information, or ...