Output Terminal Function Selection (Pr. 190 To Pr. 195) - Mitsubishi Electric FR-A520-2.2K Instruction Manual

z

Output terminal function selection (Pr. 190 to Pr. 195)

Pr. 190 "RUN terminal function selection"
Pr. 191 "SU terminal function selection"
Pr. 192 "IPF terminal function selection"
Pr. 193 "OL terminal function selection"
Pr. 194 "FU terminal function selection"
Pr. 195 "ABC terminal function selection"
You can change the functions of the open collector and contact output terminals.
Parameter Terminal
Factory Setting
Number Symbol
190 RUN
191 SU
192 IPF
193 OL
194 FU
195 A, B, C
<Setting>
Refer to the following table and set the parameters:
Setting
Signal
Positive Negative
Name
logic logic
0 100 RUN Inverter running
1 101 SU Up to frequency
Instantaneous power failure or
2 102 IPF
undervoltage
3 103 OL Overload alarm
4 104 FU Output frequency detection
Second output frequency
5 105 FU2
detection
Third output frequency
6 106 FU3
detection
7 107 RBP Regenerative brake pre-alarm
Electronic overcurrent
8 108 THP
protection pre-alarm
9 109 PRG Programmed mode
10 110 PU PU operation mode
11 111 RY Inverter operation ready
12 112 Y12 Output current detection
13 113 Y13 Zero current detection
14 114 FDN PID lower limit
15 115 FUP PID upper limit
PID forward-reverse rotation
16 116 RL
output
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Factory-Set Terminal
Function
0 Inverter running
1 Up to frequency
Instantaneous power
2
failure/undervoltage
3 Overload alarm
4 Frequency detection
99 Alarm output
Function
Output during operation when the inverter output
frequency rises to or above the starting frequency.
Refer to Pr. 41 "up-to-frequency sensitivity". (Note
2)
Output when an instantaneous power failure or
undervoltage occurs.
Output while stall prevention function is activated.
Refer to Pr. 42, Pr. 43 (output frequency
detection).
Refer to Pr. 50 (second output frequency
detection).
Refer to Pr. 116 (third output frequency
detection).
Output when 85% of the regenerative brake duty
set in Pr. 70 is reached.
Output when the cumulative electronic
overcurrent protection value reaches 85% of the
preset level.
Output in the programmed mode. (Note 3)
Output when the PU operation mode is selected.
Output when the inverter can be started by
switching the start signal on or while it is running.
Refer to Pr. 150 and Pr. 151 (output current
detection).
Refer to Pr. 152 and Pr. 153 (zero current
detection).
Refer to Pr. 128 to Pr. 134 (PID control).
144
PARAMETERS
Related parameter
Pr. 76 "operation mode selection"
Setting Range
0 to 199, 9999
0 to 199, 9999
0 to 199, 9999
0 to 199, 9999
0 to 199, 9999
0 to 199, 9999
Operation
Pr. 66, Pr. 148,
Pr. 79, Pr. 200
Pr. 17 = 0 to 3
Pr. 150, Pr. 151
Pr. 152, Pr. 153
Related
parameter

Pr. 41

Pr. 22, Pr. 23,
Pr.1, Pr. 149,
Pr. 154
Pr. 42, Pr. 43
Pr. 50
Pr. 116
Pr. 70
Pr. 9
to Pr. 231

Pr. 128 to
Pr. 134