Mitsubishi Electric FR-A520-2.2K Instruction Manual page 155

<Setting>
Refer to the following list and set the parameters:
Signal
Setting
Name
Pr. 59 = 0
Pr. 59 = 1, 2
0 RL
Pr. 79 = 5
Pr. 270 = 1, 3 *
Pr. 59 = 0
Pr. 59 = 1, 2
1 RM
Pr. 79 = 5
Pr. 59 = 0
Pr. 59 = 1, 2
2 RH
Pr. 79 = 5
Second function selection
3 RT
Pr.270 = 1, 3
4 AU Current input selection
5 JOG Jog operation selection
6 CS Automatic restart after instantaneous power failure selection
External thermal relay input**
The externally provided overheat protection thermal relay,
7 OH
motor-embedded temperature relay or the like is operated to
stop the inverter.
8 REX 15-speed selection (combination with RL, RM, RH)
9 X9 Third function
10 X10 FR-HC connection (inverter operation enable)
11 X11 FR-HC connection (instantaneous power failure detection)
12 X12 PU operation external interlock
13 X13 External DC dynamic braking start
14 X14 PID control valid terminal
15 BRI Brake opening completion signal
16 X16 PU-external operation switch-over
17 X17 Load pattern selection forward/reverse rotation boost
18 X18 Advanced magnetic flux vector-V/F switch-over
19 X19 Load torque high-speed frequency
20 X20 S-pattern acceleration/deceleration C switch-over terminal
(only when FR-A5AP option is fitted)
22 X22 Orientation command (Note 11) (only when FR-A5AP option
is fitted)
23 LX Pre-excitation (Note 2) (only when FR-A5AP option is fitted)
9999 No function
*: When Pr. 59 = "1 or 2", Pr. 79 = "5", and Pr. 270 = "1 or 3", the functions of the RL, RM, RH and RT signals change as listed above.
**: Operated when the relay contact "opens".
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Functions
Low-speed operation command
* Remote setting (acceleration)
Programmed operation group
*
selection
Stop-on-contact selection 0
Middle-speed operation command
* Remote setting (deceleration)
Programmed operation group
*
selection
High-speed operation command
* Remote setting (setting clear)
Programmed operation group
*
selection
* Stop-on-contact selection 1
142
PARAMETERS
Relevant Parameters
Pr. 4 to Pr. 6
Pr. 24 to Pr. 27
Pr. 232 to Pr. 239
Pr. 59
Pr. 79, Pr. 200, Pr. 201 to Pr. 210, Pr.
211 to Pr. 220, Pr. 221 to Pr. 230, Pr.
231
Pr. 270, Pr. 275, Pr. 276
Pr. 4 to Pr. 6, Pr. 24 to Pr. 27, Pr. 232 to
Pr. 239
Pr. 59
Pr. 79, Pr. 200, Pr. 201 to Pr. 210, Pr.
211 to Pr. 220, Pr. 221 to Pr. 230, Pr.
231
Pr. 4 to Pr. 6, Pr. 24 to Pr. 27,
Pr. 232 to Pr. 239
Pr. 59
Pr. 79, Pr. 200, Pr. 201 to Pr. 210, Pr.
211 to Pr. 220, Pr. 221 to Pr. 230, Pr.
231
Pr. 44 to Pr. 50
Pr. 270, Pr. 275, Pr. 276
Refer to page 10
Pr. 15, Pr. 16
Pr. 57, Pr. 58, Pr. 162 to Pr. 165
Refer to page 174
Pr. 4 to Pr. 6, Pr. 24 to Pr. 27,
Pr. 232 to Pr. 239
Pr. 110 to Pr. 116
Pr. 30, Pr. 70
Pr. 30, Pr. 70
Pr. 79
Pr. 10 to Pr. 12
Pr. 128 to Pr. 134
Pr. 278 to Pr. 285
Pr. 79
Pr. 14
Pr. 80, Pr. 81, Pr. 89
Pr. 271 to Pr. 274
Pr. 380 to Pr. 383
Pr. 350 to Pr. 369
Pr. 80, Pr.81, Pr. 359, Pr. 369, Pr. 370