Yeedi K600, K602G - Robot Vacuum Manual

Also See for K600:

Instruction manual (72 pages)

Table of Contents

Contents

1 Package Contents
- 1.1 Product Diagram
2 Operating and Programming
3 Maintenance
4 Indicator Light and Alarm Sounds
5 Troubleshooting
6 Technical Specifications
7 Documents / Resources
- 7.1 Download manual

Yeedi K600, K602G - Robot Vacuum Manual

Package Contents

Note: Figures and illustrations are for reference only and may differ from actual product appearance.
Product design and specifications are subject to changes without notice.

Product Diagram

Robot
Product Diagram - Part 1 - Robot

Bottom View
Product Diagram - Part 2 - Bottom View
Product Diagram - Part 3 - Charging Dock and Remote Control

Operating and Programming

Notes Before Cleaning

Do not use the robot on wet surfaces or surfaces with standing water.

Before using the product on a rug with tasseled edges, please fold the rug edges under.

It may be necessary to place a physical barrier at the edge of a drop to stop the unit from falling over the edge

Tidy up the area to be cleaned by putting furniture, such as chairs, in their proper place

Remove power cords and small objects from the floor that the robot could be obstructed by.

Preparation

Plug in Adapter
Charging Dock Placement
Install Side Brushes
Power ON
Charge the robot

Note: When the robot completes the cleaning cycle or when battery power gets low, the robot automatically returns to the Charging Dock to recharge itself

Selecting Cleaning Mode

AUTO Cleaning Mode
A Random Cleaning Pattern (optimized for carpets) will be selected by default.
Return to Docking Station
Edge Cleaning Mode
Spot Cleaning Mode

Switch vacuum power

Pause, Wake Up, Power Off

Pause

Note: the robot's Control Panel stops glowing after the robot is paused for a few minute. Press the AUTO Mode Button on the robot to wake up the robot.
Wake Up
Power OFF

Note: When the robot is not working, it is recommended to keep it switched ON and charging

Maintenance

Dust Bin and Filters

Maintenance - Dust bin

Main Brush and Side Brushes

Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Maintenance - Main Brush
Maintenance - Side Brushes

Other Components

Maintenance - Other Components

Note: Before cleaning the robot's Charging Contacts and Charging Dock Pins, turn the robot OFF and unplug the Charging Dock.

Regular Maintenance

To keep the robot running at peak performance, perform maintenance tasks and replace parts with the following frequencies:

Robot Part	Maintenance Frequency	Replacement Frequency
Side Brush	Once every 2 weeks	Every 3-6 months
Main Brush	Once per week	Every 6-12 months
Sponge Filter/ High Efficiency Filter	Once per week	Every 3-6 months
Universal Wheel Anti-Drop Sensors Bumper Charging Contacts Charging Dock Pins	Once per week	/

A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Note: YEEDI manufactures various replacement parts and fittings Please contact Customer Service for more information on replacement parts

Indicator Light and Alarm Sounds

Indicator Light

Status	AUTO Mode Button
The robot is charging	Flashes BLUE
The robot has a problem	Flashes RED or glows a continuous RED
The robot has low battery	Glows a continuous RED
The robot is cleaning	Glows a continuous BLUE

Alarm Sounds
If the robot detects a problem, it emits alarm beeps and the AUTO Mode Button flashes RED or glows RED

Flashing RED:

Alarm Sound	Problems	Solution
Two Beeps	Anti-Collision Bumper Malfunction	Check the Anti-Collision Bumper for debris and remove the debris
Three Beeps	Anti-Drop Sensors Malfunction	Clean Anti-Drop Sensors as described in Maintenance section
Four Beeps	Low Battery	Manually place the robot on the Charging Dock to charge

Glowing a continuous RED:

Alarm Sound	Problems	Solution
One Beep	Driving Wheel malfunction	Check Driving Wheel for tangled hair or debris and clean as described in Maintenance section
Two Beeps	Side Brush malfunction	Check Side Brushes for tangled hair or debris and clean as described in Maintenance section
Four Beeps	Main Brush malfunction	Check Main Brush for tangled hair or debris and clean as described in Maintenance section

Troubleshooting

No.	Malfunction	Possible Causes	Solutions
1	The robot is not charging	The robot is not switched ON	Switch ON the robot
		The robot has not connected to the Charging Dock	Be sure that the robot's Charging Contacts have connected to the Charging Dock Pins
		The battery is completely discharged	Re-activate the battery Switch ON the robot Place the robot on the Charging Dock by hand, remove after charging for 3 minutes, repeat 3 times; then charge normally
2	The robot cannot return to the Charging Dock	The Charging Dock is not correctly placed	Place the Charging Dock correctly
3	The robot gets stuck while working and stops	The robot is tangled with something on the floor (electrical wires, curtains, carpet fringing, etc)	The robot will try various ways to free itself If it is unsuccessful, manually remove the obstacles and restart
4	The robot returns to the Charging Dock before it has finished cleaning	When the battery gets low, the robot automatically switches to Return to Charger Mode and returns to the Charging Dock to recharge itself	This is normal No solution necessary
4		Working time varies according to floor surface, room complexity and the Cleaning Mode selected	This is normal No solution necessary
5	The robot does not clean the whole area	The cleaning area is not tidy	Remove small objects from the floor and tidy up the cleaning area before the robot starts cleaning

Technical Specifications

Model	K602G
Rated Input	19V DC 06A 114W
Charging Dock
Rated Output Voltage	19V DC	Rated Output Current	06A
Power Adapter Model	DK18-190060H-U
Rated Input	100-120V AC 50-60Hz 05A
Rated Output	19V DC 06A