Empire Comfort Systems White Mountain Hearth Tahoe DVCX42FP30P Installation Instructions And Owner's Manual page 64

FOR THE HOMEOWNER
• This fireplace must be installed and serviced by your dealer or
a qualified service technician. Other than cleaning the glass
and replacing the light bulbs, there are no user-serviceable
components.
• Keep the area around the fireplace clean and free of debris. This
fireplace requires an unimpeded flow of air to circulate warm air.
Do not place objects on or around the fireplace that may restrict
air flow.
• Keep the area around the fireplace free of combustible materials
– including drapery, upholstered furniture, paper, boxes, and
clothing. Never hang stockings or cards above the fireplace.
• Never operate the fireplace with the glass front removed or
damaged. Any part removed for cleaning or servicing must be
replaced prior to operating the fireplace.
• The fireplace gets hot during operation and may remain hot for an
hour after use. When operated by thermostat, the fireplace will
turn on and off automatically.
• This fireplace may become hot enough to burn skin and ignite
clothing after prolonged contact. To prevent injury, alert people in
your home – especially children – to the hazards of high surface
temperatures and warn them to stay away from the fireplace.
• Supervise children whenever the fireplace is hot. Young children
and others may be susceptible to accidental contract burns. Have
your dealer install a physical barrier if there are at-risk individuals
in your home. To restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young children, and other
at-risk individuals out of the room and away from hot surfaces.
• The vent cap, located on the outside of your home, will also become
very hot. Alert everyone, adults and children, to stay clear and avoid
touching the vent cap. Keep the area around the vent cap clear of
combustibles, including shrubs and trees.
• Do not use this fireplace if any part has been underwater. Have a
qualified technician inspect the fireplace and replace any part that
has been underwater. In the event of a natural disaster (tornado,
earthquake, fire, etc.) have a qualified technician inspect the
fireplace for damage or potential gas leaks. Repair or replace any
damaged components before operating this fireplace.
• Never burn solid fuels such as wood, coal, paper or cardboard in
this fireplace.
Annual Inspection
• Have the fireplace inspected annually before use.
•
More frequent inspection and cleaning may be required if the
fireplace is installed in an area exposed to pet hair or dust, or to
excessive lint from new carpeting or bedding materials.
During The Annual Checkup, The Technician Will:
• Inspect the pilot (flame safety system) and burner(s) for proper
operation and replace any damaged parts.
• Check the glass and gasket for proper seal.
• Vacuum and clean any foreign debris in the firebox that is not
supposed to be there.
• Clean Glass with a suitable fireplace glass cleaner. Abrasive
cleaners must not be used. Be careful not to scratch the glass
when cleaning.
• Check the barrier screen for fit and structural integrity. See Page
63. Check all latches or other door retention components for
proper operation, tension, and relief mechanisms are free from
obstructions. See Page 63.
• Inspect the log set (if applicable) and decorative media (if
applicable) for debris or damage.
• Freshen up the glowing embers if applicable.
• Replace batteries in the remote transmitter and receiver if
applicable.
• Inspect the venting and vent termination cap for damage,
corrosion, sooting, or obstruction and correct if present.
• In addition, clean and inspect the fireplace following any
remodeling work in your home.
Page 64
MAINTENANCE AND SERVICE
FOR THE INSTALLER
Maintenance Precautions
Installation and repair should be done by a qualified service person.
The fireplace should be inspected before use and at
least annually by a qualified service person. More frequent cleaning
might be required due to excessive lint from carpeting, bedding
material, etc.
Keep burner and control compartment clean.
Examine venting system periodically and replace damaged parts.
Make a periodic visual check of pilot and burners. Clean and replace
damaged parts.
Damaged Fireplace
Do not use this fireplace if any part has been under water. Immediately
call a qualified service technician to inspect the fireplace and to replace
any part of the control system and any gas control which has been
under water.
In the event of a natural disaster (tornado, earthquake, fire, etc.) have
a qualified technician inspect the fireplace for damage or potential gas
leaks. Repair or replace any damaged components before operating
this fireplace.
Annual Inspection
• Have the fireplace inspected annually before use.
• More frequent inspection and cleaning may be required if the
fireplace is installed in an area exposed to pet hair or dust, or to
excessive lint from new carpeting or bedding materials.
During The Annual Checkup, The Technician Will:
• Inspect the pilot (flame safety system) and burner(s) for proper
operation and replace any damaged parts.
• Test and measure the flame failure response time of the flame
safety system. It must de-energize the safety shut-off in no more
than 30 seconds.
• Vacuum and clean any foreign debris in the firebox that is not
supposed to be there.
• Inspect and ensure that the lighting of the main burner occurs
within 4 seconds of the gas valve opening. Visual inspection
should match the information illustrated in the manual. Inspect
primary air openings for blockage.
• Check the glass and gasket for proper seal.
• Clean Glass with a suitable fireplace glass cleaner. Abrasive
cleaners must not be used. Be careful not to scratch the glass
when cleaning.
• Check all latches or other door retention components for
proper operation, tension, and relief mechanisms are free
from obstructions. See Page 63.
• Check the barrier screen for fit and structural integrity.
See Page 63.
• Inspect the log set (if applicable) and decorative media
(if applicable) for debris or damage.
• Freshen up the glowing embers if applicable.
• Replace batteries in the remote transmitter and receiver
if applicable.
• Inspect the venting and vent termination cap for damage, corrosion,
sooting, or obstruction and correct if present.
• Check all accessible gas-carrying tubes, connections,
pipes and other components for leaks.
•
In addition, clean and inspect the fireplace following any
remodeling work in your home.
39634-2-0720