Empire Comfort Systems DVCP36(PP,SP)30(N,P)-1 Installation Instructions And Owner's Manual
  1. Manuals
  2. Brands
  3. Empire Comfort Systems Manuals
  4. Indoor Fireplace
  5. DVCP36(PP
  6. Installation instructions and owner's manual
Empire Comfort Systems DVCP36(PP,SP)30(N,P)-1 Installation Instructions And Owner's Manual

Empire Comfort Systems DVCP36(PP,SP)30(N,P)-1 Installation Instructions And Owner's Manual

Direct vent zero clearance gas fireplace heater
Hide thumbs
Table of Contents

Advertisement

Quick Links

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death or
property damage.
— Do not store or use gasoline or other
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
not use any phone in your building.
from a neighbor's phone. Follow the
gas supplier's instructions.
— Installation and service must be
agency or the gas supplier.
If not installed, operated and maintained in
accordance with the manufacturer's instructions,
this product could expose you to substances in
fuel or from fuel combustion which can cause
death or serious illness.
WARNING
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.
NOTICE
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING
WARNING
HOT GLASS
WILL
CAUSE BURNS.
DO NOT TOUCH
UNTIL COOLED.
NEVER
ALLOW CHILDREN
TO TOUCH GLASS.
DIRECT VENT ZERO CLEARANCE
GAS FIREPLACE HEATER
INTERMITTENT PILOT (IPI)
UL FILE NO. MH30033
This appliance may be installed in an
aftermarket, permanently located,
manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
GLASS
MODEL SERIES:
MILLIVOLT (MV)
DVCP36(PP,SP)30(N,P)-1
DVCP36(PP,SP)70(N,P)-1
GAS-FIRED
Page 1

Advertisement

Table of Contents
loading

Related Manuals for Empire Comfort Systems DVCP36(PP,SP)30(N,P)-1

Summary of Contents for Empire Comfort Systems DVCP36(PP,SP)30(N,P)-1

  • Page 1 Failure to follow safety warnings exactly GAS-FIRED could result in serious injury, death or MILLIVOLT (MV) property damage. DVCP36(PP,SP)30(N,P)-1 — Do not store or use gasoline or other INTERMITTENT PILOT (IPI) vicinity of this or any other appliance. DVCP36(PP,SP)70(N,P)-1 — WHAT TO DO IF YOU SMELL GAS UL FILE NO.
  • Page 2 BEFORE YOU START NOTICE DANGER be damaged if force is applied to their surfaces. Take care not to push against barrier screens. Indicates a hazardous situation which, if not avoided, will result Cut binding straps and shrink wrap. Shrink wrap should be in death or serious injury.
  • Page 3 CARTON CONTENTS & HARDWARE PACK CARTON CONTENTS - DVCP36(PP,SP)3 SERIES CARTON CONTENTS - DVCP36(PP,SP)7 SERIES NAT Unit LP Unit NAT Unit LP Unit Items not shown to scale. Items not shown to scale. QUANTITY INDEX QUANTITY INDEX NO. DESCRIPTION DESCRIPTION SUPPLIED NUMBER SUPPLIED...

  • Page 4: Table Of Contents

    TABLE OF CONTENTS SECTION PAGE Introduction ............................... 5 ............................6 Accessories ............................... 7 Blower Installation ..........................8 - 9 Fireplace Dimensions - See-Thru ......................10 Fireplace Dimensions - Peninsula ......................11 Clearances ............................12 - 13 Combustible Material ..........................13 Vent Termination Clearances ......................14 - 15 Gas Supply ...............................

  • Page 5: Introduction

    INTRODUCTION Instructions to Installer Any alteration of the original design, installed other than as shown in these instructions or use with a type of gas not Leave instruction manual with owner after installation. shown on the rating plate is the responsibility of the person and company making the change.
  • Page 6 SPECIFICATIONS NATURAL GAS PENINSULA SEE-THRU PENINSULA SEE-THRU MODELS MODELS MODELS MODELS Input BTU/Hr Maximum 34,000 34,000 32,500 32,500 Input BTU/Hr Minimum 23,000 23,000 26,000 26,000 KWH (Maximum) 9.96 9.96 9.38 9.38 KWH (Minimum) 6.74 6.74 7.76 7.76 3/16in 3/16in Air Shutter Opening* (1/8in w/40ft.

  • Page 7: Accessories

    ACCESSORIES 62220-2623. Model Number Description May Be Used On **DVP36PRB Peninsula & See-Thru Models **DVP36PFLKR Vertical Fluted Black Liner Peninsula & See-Thru Models **DVP36PKR Porcelain Black Liner Peninsula & See-Thru Models FBB14 Blower Kit Peninsula & See-Thru Models Light Kit Peninsula &...

  • Page 8: Blower Installation

    BLOWER INSTALLATION Snap the fan control disc into the forked prongs on the valve Remove the glass and screen frames, and the bottom bracket. See Figure 3. access panel from the side which is opposite the valve. The glass and screen frame may be removed as a unit. It is not necessary to separate the screen frame from the glass frame.
  • Page 9 BLOWER INSTALLATION BLOWER ASSEMBLY PARTS LIST INDEX PART DESCRIPTION 36118 R7649 FAN, CONTROL L120-20 R3529 R4192 R4186 10088 R11768 36092-0-0815 Page 9...

  • Page 10: Fireplace Dimensions - See-Thru

    FIREPLACE DIMENSIONS - SEE-THRU (TO CENTER OF VERTICALLY ORIENTED ELBOW) INDEX DVCP36SP(30,70) DIMENSION DESCRIPTION LETTER (Dimensions in Inches) 39-1/4 31-1/2 37-1/4 20-1/4 42-3/8 Width from the left side of the box to the centerline of vertical vent 48-5/8 Depth from back of box to centerline of vent Height from the bottom of the box to the gas line opening 1-3/8 Depth from the front of the box to gas line opening...

  • Page 11: Fireplace Dimensions - Peninsula

    FIREPLACE DIMENSIONS - PENINSULA (TO CENTER OF VERTICALLY- ORIENTED ELBOW) INDEX DVCP36PP(30,70) DIMENSION DESCRIPTION LETTER (Dimensions in Inches) 39-1/4 31-1/2 37-1/4 20-1/4 42-3/8 Width from the left side of the box to the centerline of vent 45-5/8 Depth from back of box to centerline of vent Height from the bottom of the box to the gas line opening 1-3/8 Depth from the front of the box to gas line opening...

  • Page 12: Clearances

    CLEARANCES Television Considerations FINISHED TV manufacturers recommend against placing their products VERTICAL FRAMING WALL near a heat source. NON-COMBUSTIBLE WALL COVERING (COVER SEAM) Systems accepts no responsibility for damage or injuries. Follow HORIZONTAL FRAMING the television manufacturer’s installation instructions, including 3”...

  • Page 13: Combustible Material

    CLEARANCES Mantel Chart MANTEL COMBUSTIBLE TRIM AND MANTELS ALLOWED IN SHADED AREA SEAM BETWEEN NON-COMBUSTIBLE BOARD AND DRYWALL NON- 16” NON-COMBUSTIBLE COMBUSTIBLE BOARD HEIGHT - ALL FINISH VISIBLE SIDES OF UNIT. MATERIAL MUST COVER THE SURFACE OF THE FIREPLACE FACE TO TOP OF FIREPLACE OPENING...

  • Page 14: Vent Termination Clearances

    VENT TERMINATION CLEARANCES Termination clearance for buildings with combustible and noncombustible exteriors. Figure 11 Vertical Sidewall Installations The horizontal vent run refers to the total length of vent pipe from Important! Minimum clearance between vent pipes and combustible materials is 3 inch on top, and 1 inch on bottom and sides.

  • Page 15: Vent Termination Clearances

    VENT TERMINATION CLEARANCES Canadian Installations1 US Installations2 Canadian Installations1 US Installations2 A= Clearance above grade, I= Clearance to service veranda, porch, deck, or 12 in 12 in 3 ft regulator vent outlet balcony J= Clearance to nonmechanical air B= Clearance to window or 12 in 9 in supply inlet to building or...

  • Page 16: Gas Supply

    GAS SUPPLY The gas pipeline can be brought in through the vent-end of the GAS SUPPLY PRESSURE (INCHES W.C.) Z223.1 installation code. MINIMUM NORMAL MAXIMUM RECOMMENDED GAS PIPE DIAMETER Natural Gas 14.0 SCHEDULE 40 PIPE TUBING, TYPE L LP (Propane) 10.8 11.0 14.0...

  • Page 17: Locating Fireplace

    LOCATING FIREPLACE NOTICE: Island and Room Divider installation is possible as long as the horizontal portion of the vent system does not exceed 20 feet NOTICE is installed in the room divider or peninsula room divider positions. Figure 15 36092-0-0815 Page 17...

  • Page 18: Junction Box Wiring Installation Instructions

    JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS WARNING and shall be in compliance with all local, city and state RECEPTACLE BOX ELECTRIC building codes. Before making the electrical connection, INSIDE FIREPLACE make sure that main power supply is disconnected. The POWER IN in accordance with local codes or, in the absence of local codes, with the National Electrical Code ANSI/NFPA 70 PRE-INSTALLED...

  • Page 19: Installation

    INSTALLATION Vent Runs positioned and installed. These include the direct vent system, SUPPORT SEAMS BETWEEN DRYWALL AND NON-COMBUSTIBLE BOARD WITH FRAMING allowable vent runs. Positioning the Fireplace termination will be centered (if possible) between two studs. This will avoid any extra framing. All vent kit pipes should be 2.
  • Page 20 INSTALLATION VERTICAL FINISHED WALL FRAMING NON-COMBUSTIBLE WALL COVERING (COVER SEAM) HORIZONTAL FRAMING 3” ABOVE VENT 16” NON-COMBUSTIBLE BOARD HEIGHT - ALL VISIBLE SIDES NON-COMBUSTIBLE ZONE FIREPLACE OPENING NON-COMBUSTIBLE WALL COVERING NOTICE: See Figure 9 on page 13 for maximum mantel depth Figure 19 Clearance to Combustibles Back...
  • Page 21 INSTALLATION Framing adjusted by loosening (but do not remove) the top and bottom screws, anchoring the bracket in place using a center offs must be formed and secured. Form the top stand-offs in screw from the hardware pack, and re-tightening the top and the sequence shown in Figure 21, and secure them to the bottom screws.
  • Page 22 INSTALLATION Vertical Vent Pipe Clearance 45° ELBOW WITH HORIZONTAL TERMINATION NOTICE: 12 inches above Firebox. See Figure 26. 3” MININUM CLEARANCE TO COMBUSTIBLES IN WALL WALL THIMBLE 2” MIN. CLEARANCE VENT AROUND VENT PIPE Figure 26 46-13/16” TO COMBUSTIBLES Horizontal Vent Clearances ABOVE VENT INSIDE WALL For horizontal vent, maintain a minimum 1 inch clearance to the bottom and sides of the vent, and 3 inch clearance to...
  • Page 23 INSTALLATION Cutting the Hole Installing Support Brackets Install a horizontal pipe support used for each 3 feet of the hole through the exterior wall of the house can be cut. This horizontal run to framing members. Allow 3 inches of clearance hole must be 12-5/8in high x 10-5/8in wide with its center line to combustibles above 8 inch diameter pipe and elbows and 1 determined by the amount of vertical rise and horizontal run of...

  • Page 24: Installation

    INSTALLATION Installing Firestops NOTICE: Remove insulation from the framed area in the attic Firestops are required for safety whenever the vent system passes through an interior wall, an exterior wall, or a ceiling. NOTICE: Prevent insulation from contacting pipe after it is installed.

  • Page 25: Venting Fireplace Top

    VENTING FIREPLACE - TOP (Initial 45° Elbow Oriented Upwards) NOTICE: Figures 36 to 38 show the location and recommended openings Adjustments may be made for each particular installation. Proper Setting of Natural Gas Flue Restrictor - Figure 37 Figure 36 NOTICE: pointing in downward position.

  • Page 26: Vent Systems

    VENTING FIREPLACE - TOP Begin the vent system installation by selecting the type of venting to be installed and the path that it will take. Verify that clearances are met throughout the path of the venting system. what systems are acceptable. Check all clearances and venting components.

  • Page 27: Venting Graph

    VENTING FIREPLACE - TOP NOTICE: The initial 45° elbow is considered to be part of the EXAMPLE A: To Use the Vent Graph Determine the height of the center of the horizontal vent EXAMPLE B: pipe. Using this dimension on the Sidewall Vent Graph, locate the point it intersects with the slanted graph line.

  • Page 28: Horizontal Termination

    VENTING FIREPLACE - TOP Two Elbows One Elbow INSTALLED NOTICE: Subtract 3 feet from the total horizontal measurement VERTICALLY for each 90° elbow installed horizontally. Subtract 1-1/2 feet from the total horizontal measurement for each 45° elbow installed horizontally. INSTALLED HORIZONTALLY INSTALLED VERTICALLY...

  • Page 29: Vertical Termination

    VENTING FIREPLACE - TOP No Elbows Two Elbows INSTALLED VERTICALLY TO BOTTOM OF UNIT DIMENSIONS MINIMUM MAXIMUM EXAMPLE VENT RUNS 10ft 40ft A (Vertical) B (Horizontal Figure 46 Maximum) 10ft, 4in Three Elbows 15ft NOTICE: Subtract 3 feet from the total horizontal measurement for each 90°...
  • Page 30 VENTING FIREPLACE - TOP General Maintenance Locate and mark the center point of the vent pipe using a nail on Inspect venting system semi-annually as follows: the underside of the roof. Drive the nail through the center point. 1. Check for corrosion areas of the venting system exposed Mark the outline of the roof hole around this center point.
  • Page 31 VENTING FIREPLACE - TOP Installing the Vent System in a Chase closer than 24in. to any other vent termination or chimney of any A chase is a vertical box-like structure built to enclose the gas type. of a building may be, but are not required to be installed inside a chase.

  • Page 32: Venting Fireplace - Rear

    VENTING FIREPLACE - TOP Vertical Through the Roof Applications Your Gas Fireplace has been approved for: a) Vertical installations up to 40 feet in height. b) Two sets of 45° elbow offsets within these vertical installations. A vent pipe from 0 to a maximum of 8 feet can be used between elbows.

  • Page 33: Dvvk-5F Flex Vent Instructions

    DVVK-5F FLEX VENT INSTRUCTIONS The DVVK-5F FLEX VENT KIT includes the following components: Maintain at least ½inch rise for every 12 inches of vent run. CAUTION Because of sharp edges, always use gloves when 5” FLEX SPACER 8” FLEX VENT PIPE SPRING VENT PIPE vent terminal location, vent lengths, and clearance to...

  • Page 34: Dvvk-5F Flex Vent Instructions

    DVVK-5F FLEX VENT INSTRUCTIONS Prior to making the vent connections, apply high temperature sealant (1000°F min.) to the vent connections before securing with the band clamps provided. NOTICE: the flue pipe end without the adapter is to be installed to the Termination Cap.

  • Page 35: Finishing Installation

    FINISHING INSTALLATION installation. Non-combustible materials do not ignite or burn ceramic, concrete, slate, glass and plaster. Adhesives must be rated for high temperatures. Any mechanical fasteners used to install material must also be non-combustible, including wall test (Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750C) are considered non-combustible.

  • Page 36: Optional Fiber Or Porcelain Liners

    OPTIONAL FIBER OR PORCELAIN LINERS Order one liner for a peninsula and two for a see-through. with the screws shown on the left side of Figure 62 (Vent / Pilot side liner only). NOTICE: Use the self-drilling screws shown on the right side of Figure This sequence may be used to install liners into either side installing the log set on the burner.

  • Page 37: Glowing Embers

    GLOWING EMBERS before the logs. Refer to the instruction manual supplied with your Log Set or Mixed Log and Stones kit. Apply a single layer of shaded areas shown below. NOTICE: placement onto the burner. of embers is to be used when applying Platinum Bright burner.
  • Page 38 LOG IDENTIFICATION - LSU24SPF Part Front View Top View Description Number Log A 36018 Log B 36019 Log C 36027 Log D 36025 36021 Log F 36023 Log G 36020 Log H 36028 Log I 36022 Log J 36026 Log K 36024 Attention: When ordering parts, it is very important that part number and description coincide.

  • Page 39: Log Placement - Lsu24Spf

    LOG PLACEMENT - LSU24SPF Before you begin: Do not, handle these logs with your bare hands! Always wear gloves to prevent skin irritation. After handling logs, wash your hands gently with soap and water. All Logs The positioning of the logs is critical to the safe and clean Refer to Figure 66 for the following warning.
  • Page 40 LOG PLACEMENT - LSU24SPF Place Log H on to burner tabs 6 and 2. Place Log J onto burner tab 3. Refer to the images on this page. Page 40 36092-0-0815...
  • Page 41 LOG PLACEMENT - LSU24SPF Place Log A on to burner pins 7, 8, 9, 10 and 11. Refer to the images on this page. 36092-0-0815 Page 41...
  • Page 42 LOG PLACEMENT - LSU24SPF Page 42 36092-0-0815...
  • Page 43 LOG PLACEMENT - LSU24SPF images on this page. 36092-0-0815 Page 43...
  • Page 44 LOG PLACEMENT - LSU24SPF Place Log B onto burner tab 13 and left pin on Log A. Place Log C onto burner tab 14. Place Log K onto burner tabs 12 and 16. Refer to the images on this page. Page 44 36092-0-0815...
  • Page 45 LOG PLACEMENT - LSU24SPF 36092-0-0815 Page 45...

  • Page 46: Log Placement - Lsu24Spf

    LOG PLACEMENT - LSU24SPF Page 46 36092-0-0815...
  • Page 47 LOG & STONE IDENTIFICATION - DG30MX Part Description Front View Top View Number Stone A 36031 Stone B 36030 Stone C 36029 Stone D 36032 36033 Stone F 36037 Stone G 36034 Stone H 36035 Stone I 36036 Log J 36039 Log K 36044...
  • Page 48 LOG & STONE IDENTIFICATION - DG30MX Part Description Front View Top View Number Log L 36040 Log M 36042 Log N 36038 Log O 36043 Log P 36041 Attention: When ordering parts, it is very important that part number and description coincide. Page 48 36092-0-0815...

  • Page 49: Log & Rock Placement - Dg30Mx

    LOG & STONE PLACEMENT - DG30MX Before you begin: Do not, handle these logs with your bare hands! Always wear gloves to prevent skin irritation. After handling logs, wash your hands gently with soap and water. All Logs The positioning of the logs and rocks is critical to the safe and clean Refer to Figure 69 for the following warning.
  • Page 50 LOG & STONE PLACEMENT - DG30MX images on this page. Page 50 36092-0-0815...
  • Page 51 LOG & STONE PLACEMENT - DG30MX Place Stone A onto burner pins 7 and 8. Place Stone B onto burner pins 9 and 10. Place stone C onto burner pin 11 and burner tab 12. Refer to the images on this page. 36092-0-0815 Page 51...
  • Page 52 LOG & STONE PLACEMENT - DG30MX the images on this page. Page 52 36092-0-0815...
  • Page 53 LOG & STONE PLACEMENT - DG30MX Place Log P onto burner tab 2 and center pin on Stone B. Place Log L onto burner tab 4 and pin on Stone G. Refer to the images on this page. 36092-0-0815 Page 53...
  • Page 54 LOG & STONE PLACEMENT - DG30MX Place Log O onto burner tab 14 and left pin on Stone B. Place Log N onto burner tab 3 and right pin on Stone B. Refer to the images on this page. Page 54 36092-0-0815...
  • Page 55 LOG & STONE PLACEMENT - DG30MX tab 17 and pin on Stone D. Refer to the images on this page. 36092-0-0815 Page 55...
  • Page 56 LOG & STONE PLACEMENT - DG30MX Page 56 36092-0-0815...

  • Page 57: Millivolt Standing Pilot Operating Instructions

    MILLIVOLT STANDING PILOT OPERATING INSTRUCTIONS Millivolt System The standing pilot burns continuously even when the main burner instructions. is OFF. Initial Lighting When you ignite the pilot, the thermopile produces millivolts Remove the access panel to view the gas controls for the (electrical current) which energizes the magnet in the gas valve.
  • Page 58 MILLIVOLT STANDING PILOT OPERATING INSTRUCTIONS STANDING PILOT OPERATING INSTRUCTIONS Installation of Remote Receiver REMOTE/OFF/ON Switch OFF/ON switch. A wire as far forward as possible. harness is attached to the OFF/ON switch. The red, Attention: The Velcro loop and hook are not necessary in this black and green (wires) female push-ons attach to the installation but can be used to secure remote receiver.

  • Page 59: Millivolt Standing Pilot Wiring Diagram

    MILLIVOLT STANDING PILOT WIRING DIAGRAM (OPTIONAL) THERMOSTAT (OPTIONAL) WALL SWITCH (OPTIONAL) REMOTE CONTROL RECEIVER REMOTE/OFF/ON SWITCH (INCLUDED) REMOTE THERMOPILE GAS VALVE THERMOCOUPLE (REAR CONNECTION) PILOT Figure 74 WARNING CAUTION Electrical Grounding Instructions Label all wires prior to disconnection when servicing controls.

  • Page 60: Millivolt Standing Pilot Lighting Instructions

    MILLIVOLT STANDING PILOT LIGHTING INSTRUCTIONS WARNING sonal injury or loss of life This appliance has a pilot which must be lighted by hand. C. Use only your hand to push in or turn the gas control When lighting the pilot, follow these instructions exactly. knob.

  • Page 61: Millivolt Standing Pilot Troubleshooting

    MILLIVOLT STANDING PILOT TROUBLESHOOTING With proper installation and maintenance, your new Direct Vent Gas Fireplace will provide years of trouble-free service. If you diagnosis of problems and the corrective action to be taken. 1. Spark ignitor will not light pilot after repeated triggering —...

  • Page 62: Intermittent Pilot Electronic System Operating Instructions

    INTERMITTENT PILOT ELECTRONIC SYSTEM OPERATING INSTRUCTIONS 5.25 VDC ELECTRONIC CONTROL VALVE NOTICE: The electronic control valve system includes the ability to switch knob (regulator) that allows you to increase or decrease the the pilot from a standing pilot mode to an intermittent pilot mode. See Figure 75.

  • Page 63: Intermittent Pilot Electronic System Wiring Diagram

    INTERMITTENT PILOT ELECTRONIC SYSTEM WIRING DIAGRAM CAUTION be replaced, it must be replaced with equivalent gauge and temperature rated wire. cracked or broken. Replacement of the panel should be WARNING WARNING Electrical Grounding Instructions This module is equipped with a three-prong (grounding) Improper installation, adjustment, alteration, service or plug for your protection against shock hazard and should maintenance can cause property damage, personal injury...

  • Page 64: Intermittent Pilot Lighting Instructions

    INTERMITTENT PILOT LIGHTING INSTRUCTIONS WARNING personal injury or loss of life This appliance has a pilot which can be lighted with the C. Use only the remote control or manual remote receiver manual on/off switch, a remote control, or by switching the switch to operate the gas valve.

  • Page 65: Intermittent Pilot Control System Troubleshooting

    INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING Troubleshooting Brief Description of the Components Before proceeding with the procedures in the following troubleshooting table, verify that the power supply (AC/DC adapter) is present and that the batteries inside the receiver burner. The controls are designed to be used with either LPG or and/or optional battery pack are fresh and installed with correct polarity.
  • Page 66 INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING Page 66 36092-0-0815...
  • Page 67 INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING 36092-0-0815 Page 67...

  • Page 68: Maintenance And Service

    MAINTENANCE AND SERVICE Wiring Glass Cleaning WARNING be replaced, it must be replace with no. 18, 150°C wire or its equivalent. Do not use Ammonia based or abrasive cleaners on glass. Do not attempt to clean glass when glass is hot. NOTICE It will be necessary to clean the glass periodically.

  • Page 69: Maintenance And Service

    MAINTENANCE AND SERVICE Glass Removal and Replacement Separating Screen Frame From Glass Frame Remove bottom access panel. Turn glass and screen frame assembly upside down and rest the glass frame on a block of wood, step, or similar object. Remove glass frame and screen frames as a unit. Push downwards on screen frame to release the tabs from the glass frame.

  • Page 70: See-Thru Parts View

    PARTS VIEW SEE-THRU BURNER ASSEMBLY IP VALVE MILLIVOLT VALVE 39 40 WARNING Failure to position the parts in accordance with these with this appliance may result in property damage or personal injury. Page 70 36092-0-0815...

  • Page 71: See-Thru Parts List

    PARTS LIST SEE-THRU INDEX INDEX DESCRIPTION DESCRIPTION PART NUMBER PART NUMBER 36051 36051 STAND-OFF, LONG R11127 R11127 36053 36053 29382 29382 36074 36074 R11122 R11122 36076 36076 R2566 R2566 BLACK 34139 34139 R11128 R11128 36086 36086 R2522 R2522 SWITCH, ON/OFF 31579 31579 R11123...

  • Page 72: Peninsula Parts View

    PARTS VIEW PENINSULA BURNER ASSEMBLY IP VALVE MILLIVOLT VALVE 39 40 WARNING Failure to position the parts in accordance with these with this appliance may result in property damage or personal injury. Page 72 36092-0-0815...

  • Page 73: Peninsula Parts List

    PARTS LIST PENINSULA PART NUMBER PART NUMBER INDEX INDEX DESCRIPTION DESCRIPTION 36051 36051 STAND-OFF, LONG R10882 R10882 36053 36053 R9760 R9760 36052 36052 STAND-OFF, SHORT R3436 R3436 SWITCH 36074 36074 36045 36045 36076 36076 R11127 R11127 34139 34139 29382 29382 36086 36086 R11122...

  • Page 74: Master Parts Distributor List

    MASTER PARTS DISTRIBUTOR LIST warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below. This list changes from time to time.

  • Page 75: Important Safety Information

    IMPORTANT SAFETY INFORMATION WARNING A barrier designed to reduce the risk of burns from the Read and follow these safety precautions prior to be installed for the protection of children and other at-risk may result in death, injury, or property damage. individuals.

  • Page 76: Safety Information For Users Of Lp Gas

    SAFETY INFORMATION FOR USERS OF LP GAS SOME POINTS TO REMEMBER and explosions. In its natural state, propane is odorless Learn to recognize the odor of LP-Gas. Your local LP-Gas and colorless. You may not know all the following safety precautions which can protect both you and your family from an accident.
  • Page 77 REQUIREMENTS FOR MASSACHUSETTS For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole permanently mounted to the exterior of the building at or in part for residential purposes, including those owned or a minimum height of eight feet above grade directly in operated by the Commonwealth and where the side wall exhaust line with the exhaust vent termination for the horizontally...

  • Page 78: Appliance Service History

    APPLIANCE SERVICE HISTORY Date Dealer Name Service Technician Name Service Performed/Notes Page 78 36092-0-0815...

  • Page 79: Warranty

    WARRANTY the owner’s manual. This warranty applies to the original purchaser only and is not transferable. All warranty repairs must be accomplished Limited Lifetime Parts Warranty – Combustion Chamber, What Is Not Covered Heat Exchanger, and Factory-Installed Glass installation of this appliance. factory-installed glass fails because of defective workmanship or to and from the factory.
  • Page 80 918 Freeburg Ave. Belleville, IL 62220 If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. www.empirecomfort.com Page 80 36092-0-0815...

This manual is also suitable for:

Dvcp36(pp,sp)70(n,p)-1

Table of Contents