Table of Contents
Advertisement
Quick Links
Cab Kit
Workman
Model No. 07320—Serial No. 411900000 and Up
Important:
For 2016 and newer machines, you
must install the heavy-duty springs that are
supplied with the Cab Kit in order to use the cab
on a Workman MD/MDE/MDX/MDXD utility vehicle.
For 2015 and older machines, discard the springs
included in this kit and order 2 springs (Toro
Part No. 117-4847) from your authorized Toro
distributor.
For Workman MDE machines, the 12 V Plug
Adapter Kit (sold separately) must be installed on
the machine; refer to the Installation Instructions
for the kit.
The springs should be installed only by qualified
Toro Service Technicians using approved tools.
Improper removal, disassembly, or installation of
the spring assembly poses a danger to you and
bystanders. Please contact your authorized Toro
distributor for the appropriate tools and proper
installation of this kit.
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
MD/MDE/MDX/MDXD Utility Vehicle
Register at www.Toro.com.
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. Do not repair or revise—read the Operator's Manual.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3459-919 Rev A
Installation Instructions
93-9850
*3459-919*
decal93-9850
Advertisement
Table of Contents
Related Manuals for Toro 07320
Summary of Contents for Toro 07320
- Page 1 Safety and Instructional on a Workman MD/MDE/MDX/MDXD utility vehicle. For 2015 and older machines, discard the springs Decals included in this kit and order 2 springs (Toro Part No. 117-4847) from your authorized Toro Safety decals and instructions are distributor.
- Page 2 decal130-5964 130-5964 1. Warning—in the event of an emergency 1) Pull the locking pin out of each hinge; 2) Push the front window out to exit. decal117-4955 117-4955 1. Warning—read the Operator's Manual; wear the seat belt when seated in the operator's position; avoid tipping the machine.
-
Page 3: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Remove the strut assembly (for 2016 – No parts required and newer machines only). Install the springs (for 2016 and newer Spring machines only). -
Page 4: Preparing The Machine
Media and Additional Parts Description Qty. This kit is needed for the Workman MDE Utility Vehicle 12 V Power Plug Adapter Kit only. Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Engage the parking brake. Raise the bed until the bed prop rod is fully engaged;... - Page 5 Removing the Strut Assembly (for 2016 and Newer Machines Only) No Parts Required Procedure Raise the front of the machine off the ground and support it with jack stands. Remove the front wheel. Remove the hex-head bolt (3/8 x 4-3/4 inches) and flange nut (3/8 inch) from the spindle (Figure Remove the hex-head bolt (3/8 x 3-1/2 inches) and flange nut (3/8 inch) from the control arm (Figure...
- Page 6 3-1/2 inches) and flange nut (3/8 inch) as shown Figure Procedure Torque the hex-head bolt (3/8 x 3-1/2 inches) to Use an approved Toro spring-compression tool to 37 to 45 N∙m (27 to 33 ft-lb). remove and install springs of the strut assembly. Install the front wheel.
- Page 7 g026473 Figure 2 Using a spring compressor, remove the current g026674 Figure 3 springs and install the springs from this kit. Install the shock assemblies and turn them 3 clicks up from the longest position. Note: Refer to the Service Manual for further instructions on replacing the spring and checking the front end toe of the tires.
-
Page 8: Installing The Side Panels
Secure the frame to the machine using 10 bolts (3/8 x 3/4 inch), 10 nuts (3/8 inch), and 4 bolts (3/8 x 7/8 inch) as shown in Figure g026277 Figure 4 1. Bolt (5/16 inch) 5. Nut (3/8 inch) 2. Bolt (3/8 x 7/8 inch) 6. - Page 9 g026673 Figure 8 1. Bolt (7/16 inch) 3. Nut (7/16 inch) 2. Bolt (3/8 x 7/8 inch) Torque the 4 bolts (3/8 inch) to 37 to 45 N∙m (27 to 33 ft-lb). Mount the retractable end of each seat-belt g026279 assembly to each seat-belt anchor bracket with Figure 7 a bolt (7/16 inch) and a nut (7/16 inch) as shown...
- Page 10 Using the dimensions shown in Figure locate, mark, and drill 2 holes in the top of the seat shroud. Important: Use caution when drilling these Routing the Wire Harness holes; electrical components and control cables are located under the seat shroud. Parts needed for this procedure: Wire harness Clip tie...
- Page 11 g416543 Figure 12 For Workman MDX/MDXD machines: Connect the ring terminal on the harness to the grounding block on the center dash support (A of Figure 14) and insert the fuse-block connector and the fuse (30 A) into an available fuse-block connection (B of Figure 14).
- Page 12 14). Note: If there is not an available fuse-block connection, you need to add a fuse block to the fuse-block grouping. Contact your authorized Toro distributor for more information. g416744 Figure 15 1. Ring terminal 4. Power-adapter harness 2. Ground-adapter harness 5.
-
Page 13: Product Overview
Product Overview Controls Control Panel Windshield-Wiper Switch Push the top of the switch to activate the windshield wipers (Figure 16). g026274 Figure 16 1. Windshield-wiper switch 2. Light switch Light Switch Push the light plate to turn on the light (Figure 16). - Page 14 Notes:...
- Page 15 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.