Related Manuals for Hohner IT 210
Summary of Contents for Hohner IT 210
- Page 1 Operating Manual Level Converter, Direction Signal Decoder and programmable Pulse Divider IT 210 Your partner for standard and special designs - precise, reliable and fast -...
- Page 2 9 to 30 VDC power supply • motrona GmbH, Zeppelinstraße 16, DE - 78244 Gottmadingen, Tel. +49 (0) 7731 9332-0, Fax +49 (0) 7731 9332-30, info@motrona.com, www.motrona.com Hohner Elektrotechnik GmbH Gewerbehof 1 D-59368 Werne Phone +49 - 2389 - 9878-0 +49 - 2389 - 9878-27 E-Mail info@hohner-elektrotechnik.de...
-
Page 3: Table Of Contents
2018 Legal notices: All contents included in this manual are protected by the terms of use and copyrights of Hohner Elektrotechnik GmbH. Any reproduction, modification, usage or publication in other electronic and printed media as well as in the internet requires prior written authorization by Hohner Elektrotechnik GmbH. - Page 4 Legal notices: All contents included in this manual are protected by the terms of use and copyrights of Hohner Elektrotechnik GmbH. Any reproduction, modification, usage or publication in other electronic and printed media as well as in the internet requires prior written authorization by Hohner Elektrotechnik GmbH.
-
Page 5: Safety Instructions And Responsibility
- in accordance to the “Technical Specifications” (see chapter 8). The device is not suitable for operation in explosion-proof areas or areas which are excluded by the EN 61010-1 standard. It210_01a_oi_e.docx / Jan-20 Page 4 / 21 www.hohner-elektrotechnik.de... -
Page 6: Installation
Please find all respective hints and rules on www.hohner-elektrotechnik.de. 1.4 Cleaning, Maintenance and Service Notes To clean the front of the unit please use only a slightly damp (not wet!), soft cloth. - Page 7 (if necessary). Unauthorized opening and repairing can have negative effects or failures to the protection-measures of the unit. It210_01a_oi_e.docx / Jan-20 Page 6 / 21 www.hohner-elektrotechnik.de...
-
Page 8: Introduction
All settings are made on the DILL switches on the housing. The device consists of a compact housing with screw terminals and can be mounted on a DIN rail.Block diagram 3. Block diagram It210_01a_oi_e.docx / Jan-20 Page 7 / 21 www.hohner-elektrotechnik.de... -
Page 9: Terminal Assignments And Connections
A/B. It210_01a_oi_e.docx / Jan-20 Page 8 / 21 www.hohner-elektrotechnik.de... - Page 10 Output Mode : A/B Dir (Pulse / Direction) Output Mode : A/B 90° ON ZERO_A : Zero setting delayed, no errors ZERO_A : Zero setting immediately, error possible Configuration DIL2 (Front 3-pole) It210_01a_oi_e.docx / Jan-20 Page 9 / 21 www.hohner-elektrotechnik.de...
-
Page 11: Progarmmable A/B Divider
BOUT output signal. (A/B dir). There is no division. Case 2: Input A/B Dir, Output A/B 90° DIL1/6 = ON, DIL1/7 = OFF with A/B Divider setting: DIL5, 6 = all OFF It210_01a_oi_e.docx / Jan-20 Page 10 / 21 www.hohner-elektrotechnik.de... -
Page 12: Setting The A/B Divider (At A/B Dir To A/B 90°)
ON ON ON ON ON ON ON ON ON ON 1 : 4096 Example: Input A/B dir, output A/B 90 ° with A/B division 1:6 (setting DIL6, 5: OFF ON OFF) Division 1:2: See Input/Output Mode Conversion (A/B Divider: All OFF) It210_01a_oi_e.docx / Jan-20 Page 11 / 21 www.hohner-elektrotechnik.de... -
Page 13: Setting The A/B Divider (For All Other Modes)
Example: Input A/B 90°, output A/B 90 ° with A/B division 1:3 (setting DIL6, 5: OFF ON OFF Example: Input A/B 90°, output A/B 90 ° with A/B division 1:3 (setting DIL6, 5: OFF ON OFF It210_01a_oi_e.docx / Jan-20 Page 12 / 21 www.hohner-elektrotechnik.de... - Page 14 It210_01a_oi_e.docx / Jan-20 Page 13 / 21 www.hohner-elektrotechnik.de...
-
Page 15: Setting To Zero The A/B Divider With Zero_A Signal
5.6. Informationen over the signal change A/B Dir Signal changes from B (direction) should appear shortly before or latest at the same time as the A flank so that the change can be detected correctly. It210_01a_oi_e.docx / Jan-20 Page 14 / 21 www.hohner-elektrotechnik.de... -
Page 16: Programmable Z Divider
ON OFF ON ON ON ON ON ON 1 : 254 OFF ON ON ON ON ON ON ON 1 : 255 ON ON ON ON ON ON ON ON 1 : 256 It210_01a_oi_e.docx / Jan-20 Page 15 / 21 www.hohner-elektrotechnik.de... -
Page 17: Location And Width Of The Z Pulse
Narrow Z pulse (1/4 output-periode) Front (Only applicable to input signals A/B 90°, DIL1/6 = OFF) 8-pole OFF ON The pulse width at the output corresponds to ¼ period of pulse width at the input. It210_01a_oi_e.docx / Jan-20 Page 16 / 21 www.hohner-elektrotechnik.de... -
Page 18: Independent Z Divider
A/B signal does not affect the counting sequence (additionally DIL2/1 on OFF, ZIN is used, Z divider not completely set to OFF). DIL1 Front Wide Z pulse (a full encoder turn) 8-pole It210_01a_oi_e.docx / Jan-20 Page 17 / 21 www.hohner-elektrotechnik.de... -
Page 19: Automatic Generation Of A Z Pulse
ZOUT (see level conversion Z pulse). Note the special case in which the ZERO_A signal can also set the Z output to zero (see Setting to zero of the A/B divider with ZERO_A signal) It210_01a_oi_e.docx / Jan-20 Page 18 / 21 www.hohner-elektrotechnik.de... -
Page 20: Error Output
DIL switch DIL3/2 refers to the line B, /B and the DIL switch DIL3/3 to the line Z, /Z. An error can only be detected in RS-422 or HTL differential format, all other formats do not trigger an error. It210_01a_oi_e.docx / Jan-20 Page 19 / 21 www.hohner-elektrotechnik.de... -
Page 21: Dimensions
8. Dimensions It210_01a_oi_e.docx / Jan-20 Page 20 / 21 www.hohner-elektrotechnik.de... -
Page 22: Technical Specifications
-25 °C … +70 °C / -13 … +158 °F (not condensing) Failure rate: MTBF in years: 109,3 (long-term usage at 60 °C / 140 °F ) Conformity & EMC 2004/108/EC: EN 61000-6-(2-4) standards: 2011/65/EU: RoHS It210_01a_oi_e.docx / Jan-20 Page 21 / 21 www.hohner-elektrotechnik.de...