Bosch 0 601 9F0 001 Original Instructions Manual page 9

A torque characteristic depends on the following factors:
– Strength properties of the screws/nuts
– Type of backing (washer, disc spring, seal)
– Strength properties of the material being screwed/bolted
together
– Lubrication conditions at the screw/bolt connection
The following application cases result accordingly:
– A hard seat is a metal-to-metal screw application which
uses washers. After a relatively short impact duration, the
maximum torque is achieved (steep characteristic curve).
Guide values for maximum screw tightening torques
Figures given in Nm; calculated from the tensional cross-section; utilization of the yield point: 90% (with friction coefficient
µ = 0.12). As a control measure, always check the tightening torque with a torque wrench.
total
Property Classes Standard Screws/Bolts
according to
3.6 4.6
DIN 267
M6 2.71 3.61
M8 6.57 8.7
M10 13 17.5
M12 22.6 30
M14 36 48
M16 55 73
Tips
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.
Note: Ensure that no metal particles enter the power tool.
Recommendations for optimal handling of the battery
Protect the battery against moisture and water.
Only store the battery only within a temperature range of -20
to 50 °C. Do not leave the battery in your car in the summer,
for example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Maintenance and Service
Maintenance and Cleaning
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Bosch Power Tools
An unnecessarily long impact duration only causes dam-
age to the machine.
– A spring-loaded seat is also a metal-to-metal screw ap-
plication but uses spring washers, disc springs, studs or
screws/nuts with conical seats. It is also called a spring-
loaded seat when extensions are used.
– A soft seat is a screw application of e.g. metal on wood or
a screw application that uses lead washers or fibre wash-
ers as backing.
For a spring-loaded seat, as well as for a soft seat, the max-
imum tightening torque is lower than for a hard seat. A much
longer impact duration is also required.
5.6 4.8 6.6 5.8
4.52 4.8 5.42 6.02
11 11.6 13.1 14.6
22 23 26 29
37.6 40 45 50
60 65 72 79
92 98 110 122
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
High-strength Bolts
6.8 6.9 8.8 10.9
7.22 8.13 9.7 13.6
17.5 19.7 23 33
35 39 47 65
60 67 80 113
95 107 130 180
147 165 196 275
1 609 92A 70Y | (22.03.2023)
English | 9
12.9
16.2
39
78
135
215
330