Bosch 06019G010A Original Instructions Manual page 19

A light pressure on the on/off switch (17) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Preselecting torque (applies to screwdriving mode)
The torque presetting ring (7) can be used to preselect the
required torque in 25 stages. Once the set torque has been
reached, the application tool will be stopped.
Mechanical gear selection
Only operate the gear selector (9) when the power
u
tool is not in use.
First gear:
Low speed range; for working with a large drilling diameter
or for screwdriving.
Second gear:
High speed range; for working with a small drilling diameter.
Always push the gear selector switch as far as it will
u
go. Otherwise, the power tool may become damaged.
Temperature-dependent overload protection
When used as intended, the power tool cannot be over-
loaded. In the event of overloading or the temperature
rising/falling outside the permitted operating temperature
range, the speed will be reduced. The power tool will not run
at full speed again until the permitted operating temperature
has been reached.
Activation of the temperature-controlled overload protector
is indicated by the LED (14) on the power tool lighting up
red. To return to within the permitted operating temperature
range, switch the gear selector (9) to first gear, run the
power tool at no load or wait until the LED (14) goes out.
When the LED (14) has gone out, the tool has returned to
within the permitted operating temperature range.
Emergency switch-off (KickBack Control)
The rapid shut-off function (KickBack Con-
trol) gives the user greater control over the
power tool and offers them better protec-
tion than power tools that do not have Kick-
Back Control. The power tool will switch off if it suddenly
and unforeseeably rotates around the drilling axis.
Rapid shut-off is indicated by the LED on the power tool
flashing.
To switch the tool back on, release the on/off switch and
then press it again.
It will no longer be possible to switch the power tool
u
on if the KickBack Control function is faulty. Have the
power tool serviced by a qualified repair person using
only original replacement parts.
Connectivity functions
In conjunction with the Bluetooth® Low Energy Module
GCY 30-4 / GCY 42, the following connectivity functions are
available for the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
Bosch Power Tools
– Management
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 30-4 /
GCY 42.
Practical advice
With the GCY 30-4 Bluetooth
u
cessory), the power tool is equipped with a radio in-
terface. Local operating restrictions, e.g. in aircraft or
hospitals, must be observed.
Only apply the power tool to the screw when the tool
u
is switched off. Rotating application tools can slip off.
An auxiliary tool can be used to remove the screwdriver bit
or universal bit holder.
Belt clip
You can use the belt clip (10) to hang the power tool on a
belt, for example. You then have both hands free and the
power tool is always at hand.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
English | 19
®
Low Energy Module (ac-
1 609 92A 6HB | (03.11.2021)