Electrical Connection - Parkside 276436 Operating And Safety Instructions Manual

• When the cutting operation is completed, move the ma-
chine head back to its upper (home) position and release
the ON/OFF button (1).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not release
the handle (2) after completing the cut; instead allow the
machine head to move upwards slowly whilst applying
light counter pressure.
Mitre cut 0°- 45° (Fig. 1, 1.3, 3)
The crosscut saw can be used to make mitre cuts of 0° -
45° in relation to the work face.
Important! To make miter cuts (inclined saw head), the
adjustable stop rail (27a) must be fixed at the outer posi-
tion.
• Open the set screw (27b) for the adjustable stop rail
(27a) with an Allen key and push the adjustable stop rail
outwards.
• The adjustable stop rail (27a) must be fixed far enough in
front of the innermost position that the distance between
the stop rail (27a) and the saw blade (5) amounts to a
maximum of 8 mm.
• Before making a cut, check that the stop rail (27a) and
the saw blade (5) cannot collide.
• Secure the locking lever (27b) again.
• Move the machine head to the top position.
• Fix the rotary table (9) in the 0° position.
• Loosen the set screw (23) and use the handle (2) to an-
gle the machine head to the left, until the pointer (25)
indicates the desired angle measurement on the scale
(24).
• Re-tighten the fixing screw (23).
• Cut as described in section "Cross-cutting".
Saw blade replacement (Fig. 5)
• Pull out the mains plug.
• Place the saw unit in „cross-cutting" position
• Unlock the moving saw blade guard (6) by pressing
the lock (3 - Fig. 1); in the process, raise the saw blade
guard so that the saw blade is free.
• Actuate the spindle lock (22 - Fig. 3).
• Loosen the saw blade fastening screw (28) - (Atten-
tion: left-handed thread).
• Remove the screw (28) and saw blade flange (29).
• Carefully remove the saw blade (risk of injury from the
saw blade teeth).
• Place a new saw blade on the inner saw blade flange. In
the process, observe the rotational direction of the saw
blade.
• Fit the outer saw blade flange and firmly tighten the
screw.
• Move the saw blade guard back to the correct position.
Replacing laser batteries (Fig. 6)
• Remove the laser battery cover (30). Remove the 2 bat-
teries.
• Replace both batteries with the same or an equivalent
type. Make sure that they are inserted with the same po-
larity as the used batteries.
• Close the battery cover.
8 GB
Switch ON / switch OFF the laser
To switch on: Move the ON/OFF (33) switch of the
laser (34) to the "1" position. A laser line is projected onto
the material you wish to process, providing an exact guide
for the cut.
To switch off: Move the ON/OFF switch of the laser
to the "0" position.
Adjusting the laser (Fig. 7)
If the laser (31) ceases to indicate the correct cutting line, you
can readjust the laser. To do so, open the screws (32) and set
the laser by moving sideways to that the laser beam strikes the
teeth of the saw blade (5).

Electrical connection

The electrical motor installed is connected
and ready for operation. The connection
complies with the applicable VDE and DIN
provisions.
The customer's mains connection as well as
the extension cable used must also comply
with these regulations.
Important information
In the event of an overloading the motor will switch itself
off. After a cool-down period (time varies) the motor can
be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Passage points, where connection cables are passed
through windows or doors.
• Kinks where the connection cable has been improperly
fastened or routed.
• Places where the connection cables have been cut due
to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regu-
larly. Make sure that the connection cable does not hang
on the power network during the inspection.
Electrical connection cables must comply with the applica-
ble VDE and DIN provisions. Only use connection cables
with the marking „H 07 RN".
The printing of the type designation on the connection ca-
ble is mandatory.
AC motor
• The mains voltage must be 230 V ~
• Extension cables up to 25 m long must have a cross-sec-
tion of 1.5 mm2.
Connections and repairs of electrical equipment
may only be carried out by an electrician.
Please provide the following information in the event of any
enquiries:
(Fig. 6)