DeWalt DWV905M Original Instructions Manual page 35

Hide thumbs Also See for DWV905M:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 28
cleaned, are to be disposed of; such items shall be
disposed of in impervious bags in accordance with any
current regulation for the disposal of such waste.
Remove the outside of the machine. It should be
decontaminated by vacuum cleaning methods and
wiped clean or treated with sealant before being taken
out of a hazardous area. All the machine parts shall
be regarded as contaminated when removed from
the hazardous area and appropriate action taken to
prevent dust dispersal.
Filter
To Remove Filters (Fig. L, M)
1. Turn on/off tool control switch 
and unplug cord from outlet.
2. Release canister latches 
from canister. Place vacuum head on a level surface
upside down.
3. For DWV905H, loosen the 2.5 mm socket head screw 
a T-10 bit, then remove the filter plate 
shown in Fig. L. Do not reuse the Class H main filter element
after it has been removed from the unit.
4. Turn each filter 
counterclockwise by gripping it on the
 9 
plastic end cover as shown in Fig. M, and carefully remove
from head, ensuring debris does not fall into mounting hole.
nOTE: Use care to not damage filter material.
5. If the bottom side of the vacuum head needs to be cleaned,
use a cloth dampened with water and mild soap and allow
it to dry. Dispose of cloth in an appropriate container.
6. Inspect filters for wear, tears or other damage.

WaRnInG: If there is any doubt on the condition of the
filters, they MUST be replaced. DO NOT continue use if
filters are damaged. Class H filters should not get cleaned
manually outside of the unit.

WARNING: Never use compressed air or a brush to clean
filters, otherwise damage to the filter membrane will occur
which will allow dust to pass through the filter. If needed,
gently tap against a hard surface or rinse with room
temperature water and let air dry. Cleaning of the filters
is typically unnecessary, even if the filter is covered with
dust. The automatic filter cleaning system will maintain
maximum performance and continue to function. If visual
damage to the filter membrane exists, replace filters. Filters
typically last between six and twelve months depending
on use and care.
To Install Filters (Fig. L, N)
1. Ensure filter seal 
is in place and is secure
 34 
2. Line up filter threads 
 35 
moderate force, turn filter clockwise until tight.
nOTE: Use care to not damage filter material.
3. For DWV905H, replace the filter plate 
screw 
 32 
on top of the plate.
4. Place the vacuum head 
by closing the canister latches 
 15 
to the OFF position ( )
and remove vacuum head 
 4 
 32 
from the filters as
 33 
to vacuum head threads and using
 33 
and tighten the
onto the container and secure it
 3 
.
 4 
Lubrication
Your dust extractor requires no additional lubrication.
Cleaning

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the appliance. These
chemicals may weaken the materials used in these parts.
Never let any liquid get inside the machine; never immerse
any part of the appliance into a liquid.
1. Vacuum the outside of the dust extractor. For further
cleaning use a cloth dampened only with water and mild
soap if necessary.
2. After use dispose of cloth in an appropriate container.
Storage (Fig. K)

CAUTION: Turn on/off tool control switch
 3 
position (O). Disconnect from the power supply.
1. Empty the canister, refer to To Empty canister
under Operation.
using
2. Clean the vacuum inside and outside.
3. Clean or replace filters, refer to Filters.
4. Remove the hose 
close the inlet with the inlet plug 
5. Put the ends of the suction hose together to prevent dirt
particles from escaping.
6. Store the suction hose and the power cord as shown in the
illustration. Place the unit in a dry room and secure it from
unauthorized use.
nOTE: Plug inlet plug into inlet to keep debris inside
canister when suction hose is removed. You can also attach
the ends of the hose together and lock together with the
twist-lock end.
nOTE: After wet applications, the internal parts of the liquid
container must be dried before storage.
Accessories

WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use of
e
such accessories with this appliance could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
ACCESSORIES
DWV9340
DWV9345
DWV9315
DWV9316
DWV9350
DWV9401
DWV9400
DWV9402
DWV9500
DWV9510
 7 
from the twist-lock hose inlet 
 20 
WALT recommended
e
Dust Class M Filter
Dust Class H Filter
Crush-proof hose
Anti-static hose;
diameter 32 mm
Floor Cleaning Kit
Paper bag
Plastic liner
Fleece bag
Vac Rack
ToughSystem®, TSTAK®
Vac Rack
EnGLIsH
15
to the OFF
 10 
and
33

Advertisement

Table of Contents
loading

Table of Contents