Related Manuals for Hyundai HCOMBI31
Summary of Contents for Hyundai HCOMBI31
- Page 1 PETROL 4IN1 TOOL HCOMBI31 WARNING: Read thoroughly the instruction manual before use...
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS SYMBOLS PRODUCT DESCRIPTION TECHNICAL INFORMATION ASSEMBLY FILLING FUEL TANK OPERATION MAINTENANCE AND STORAGE DISPOSAL TROUBLESHOOTING DECLARATION OF CONFORMITY WARRANTY PRODUCT FAILURE WARRANTY EXCLUSIONS... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS A. BRUSH CUTTER AND GRASS TRIMMER WARNING! When using this type of tool, basic precautions should always be followed to reduce the risk of fire and injury. Read all instructions carefully before attempting to use this product and retain these instructions. - Page 4 non-recommended accessories (e.g. metal multi-piece pivoting chains and flail blades) may result an accident. Ask your dealer for advice. Keep firm footing and balance during operation. Always use the harness provided. Have a correct working posture; stay stand, do not lean. The working positions should be changed regularly.
- Page 5 Never place the machine in any places where there are flammable materials (dry grass, etc.), combustible gasses or combustible liquids. When the machine is placed in storage for a long time, drain fuel from the fuel tank and carburetor, clean the parts, move the machine to a safe place and confirm that the engine is cooled down.
- Page 6 injury and damage remains. The following hazards may arise: There are harmful health consequences resulting from the emission of vibrations if the product is used for long periods of time or not managed adequately and properly maintained. The vibrations can produce the so-called “white finger” disease. If any of the symptoms of "white finger"...
- Page 7 Never refuel indoors. Never store the hedge trimmer or fuel container inside where there is an open flame, such as near a water heater. If fuel is spilled, do not attempt to start the power source, but move the hedge trimmer away from the spillage before starting.
- Page 8 Work only during in the day or with a sufficient artificial light. Before starting to work, check the condition of the tool. Ensure that all the parts of the machine are well fixed and tightened. Control regularly that the blade of cut is in good state. ...
- Page 9 and smoke containing chemicals known for their harmful effects on health. So be careful during the use of your machine and protect yourself correctly. Also avoid voluntarily breathing exhaust fumes; always hold the machine correctly when you use it. Residual risks Even if you use this product in compliance with all safety requirements, the potential risks of injury and damage remain.
- Page 10 some dysfunctions, do not use the tool and bring it to a service agent for inspection and reparation. Follow the instructions of the manual for guide-bar and chain adjustments. This shall be done with the engine stopped. National regulation can restrict the use of the machine. ...
- Page 11 Do not attempt to insert the saw into a pre-existing notch. Always make a new notch. Pay attention to moving branches or other forces that could close a notch and pinch or hinder the chain. Do not attempt to cut a branch with a diameter greater than the cutting length of the chain saw.
-
Page 12: Symbols
If any of the symptoms of "white finger syndrome" occur, seek immediate medical attention. Symptoms of the "white finger" include numbness, loss of sensitivity, tingling, tingling, and pain, loss of strength, color changes or skin condition. These symptoms usually appear on the fingers, hands or wrists. - Page 13 Wear protective and non-skid shoes Read the instruction manual Risk of projection – keep bystanders away - The distance between the machine and bystanders shall be at least 15 m. Do not use saw blades Guarantee noise level No smoking Warning! Cutting elements Caution: the accessible surface maybe hot when using the tool Keep 15 meters away from other people...
- Page 14 Poisonous fumes or toxic gases Do not expose to rain or humidity No naked fire near the machine Caution! Beware of blade thrust Warning – Risk of electric shock. Always beware of the danger from overhead electric-power line, keep a safe distance at least 10m from the power lines GASOLINE+OIL mixed 40:1 - Position: FUEL TANK CAP Chain oil tank - Position: CHINA OILTANK COVER...
-
Page 15: Product Description
3. PRODUCT DESCRIPTION 1. Hedge trimmer cover 5. Mixing bottle 2. Hedge trimmer 6. Cutting head for grass trimmer 3. Pole pruner 7. Harness 4. Saw blade cover 8. Tool kit 1. Blade for brushcutter 7. Trigger 2. Carter of protection 8. -
Page 16: Technical Information
4. TECHNICAL INFORMATION Engine information Volume of the fuel tank 800 cm³ Max engine speed 9500 min-¹ Engine idling speed 3000 min-¹ Clutch engagement speed 4510 min-¹ Engine displacement 32.5 cm³ Maximal power 0,95 kW / 7500/min Weight Min: 6,79 kg, Max: 7,91 kg Noise level and vibration Sound power level: 104,2 dB(A) Guarantee sound power level: 111dB(A) -
Page 17: Assembly
5. ASSEMBLY a. Handle Unscrew the handle. On the main unit, locate the hole; Install the rubber tap by aligning the holes (the tap is inside the handle). Install first bottom of the handle, the pin must be inserted in the hole. Install then the last part of the handle and screw it with the four screws. - Page 18 d. Blade for brushcutter Warning - sharp edges; wear gloves when manipulate the blade On the tube of the brushcutter/grass trimmer, insert a metal locking tool into the hole on the side of the drive gear and on the tool drive. Unscrew the holding nut.
- Page 19 f. Hedge trimmer There is no installation for the hedge trimmer; its tube can be directly installed on the main unit. Extension tube The provided extension tube can be installed for the hedge trimmer operation. Loosen the screw located on the tube of the hedge trimmer. Insert the extension tube in the tube of the hedge trimmer.
- Page 20 Install the guide chain on the tool and pass the chain on the wheel chain. Install the cover and tighten the fastening screw. Adjusting the chain tension The chain must not have too much clearance, but it must be possible to lift the chain a few millimeters from the guide rail.
-
Page 21: Filling Fuel Tank
Quick release mechanism Pull the strip to release the machine from you in the case of emergency. 6. FILLING FUEL TANK WARNING: When filling the tank: The tool must always be stopped and cooled. Never smoke during refueling. It must not have flames or sparks near the fuel Before refueling, allow the chainsaw to cool completely. -
Page 22: Operation
Note: DO NOT USE OTHER MIXTURES AND OTHER TYPES OF OIL / PETROL Storage of fuel The fuel must be kept in a clean and safe container and always closed. If you are not using the product for a long time, remove the fuel mixture and add it to a container. Do not leave the fuel for a long time in the product. - Page 23 Reinstall the spark plug and tighten it firmly. If a torque wrench is available, torque the spark plug to 16.7-18.6N.m. Repeat the starting procedure. If the engine still fails to start inquire with an authorized and qualified service center. 2. Stopping the operation Release the throttle trigger.
- Page 24 Scalping and edging Both of these are done with the line head tilted at a steep angle Scalping is removing top growth leaving the earth bear. Edging is trimming the grass back where it has spread over a sidewalk or drive way. During both edging and scalping, hold the unit a steep angle and in a position where the debris, and any dislodging dirt and stones, will not come back towards you even if it ricochets off the hard surface.
- Page 25 Scything weeds This is cutting by swinging the blade in a level arc. It can quickly clear areas of field grass and weeds. Scything should not be used to cut large, tough weeds or woody growths. Scything can be done in both directions, or just in one way which results in the debris being thrown away from you.
-
Page 26: Maintenance And Storage
8. MAINTENANCE AND STORAGE Before any maintenance work, the machine must be switched off and completely cooled. Maintenance shall be provided regularly and must be done according to the instructions provided in this instruction manual. A clean, well-maintained machine increases its lifetime and efficiency. - Page 27 c. Adjusting the carburetor Do not adjust carburetor unless necessary. If you have trouble with the carburetor, see your dealer. Improper adjustment may cause engine damage and void warranty. d. Fuel filter Fuel tank is fitted with a filter. Filter is situated at the free end of fuel pipe. It can be picked with a hook or similar device.
- Page 28 localized on the housing. Put the cutting string in the housing; pull correctly the string outside of the tool in equal part. Place the cover on the housing; turn it to lock it in place. h. Hedge trimmer Lubrication Regularly lubricate the blade. Use a recommended grease to do it. Ask advice to your dealer about the recommended grease to use.
- Page 29 Sprocket Examine the sprocket for signs of wear. If the wear is significant, replace it. Do not install a chain over a worn or damaged sprocket. Do not install a worn chain on a sprocket. Chain Each time, check that the cutter and the cutting angles match the diagram below.
- Page 30 The cut is not straight The vibrations increase Fuel consumption has increased Sharpening method The chainsaw should be turned off and locked before sharpening. Use a file or a round sharpening device (ask your dealer for advice). Place the file on the tooth and push forward. Go on to the next tooth by continuing this movement.
-
Page 31: Disposal
9. DISPOSAL Cutting remnants: do not throw with household rubbish or into the environment. Dispose of cutting remnants in rubbish collection centers or seek advice from your local municipality. Tool: do not dispose with household garbage. Do not throw into the environment. Remove oil and fuel from the machine, and dispose them in specific recycling centers. -
Page 32: Declaration Of Conformity
ZI, 32 RUE ARISTIDE BERGES 31270 CUGNAUX, FRANCE Tel: +33 (0)534.502.50 Fax: +33 (0)534.502.503 Declares that the machines: PETROL 4IN1TOOL Model: HCOMBI31 Serial No.: 20210853542-20210854681 the people name holding the technical file：M. Olivier Patriarca have been designed in compliance with the following standards:... -
Page 33: Warranty
12. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 34: Product Failure
13. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 35: Warranty Exclusions
14. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...