Related Manuals for Hyundai HTT50-A
Summary of Contents for Hyundai HTT50-A
- Page 1 PETROL EARTH AUGER HTT50-A1 WARNING: Read thoroughly the instruction manual before use.
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY INSTRUCTIONS............................ 3 2. YOUR PRODUCT..............................7 3. FILLING FUEL TANK............................8 4. USE................................... 9 5. MAINTENANCE AND STORAGE........................11 6. DECLARATION OF CONFORMITY......................... 12 7. WARRANTY................................13 8. PRODUCT FAILURE............................14 9. WARRANTY EXCLUSIONS..........................15... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS 1.1 GENERAL SECURITY INSTRUCTIONS THIS MACHINE MAY CAUSE SERIOUS INJURIES. Read the instructions carefully for handling, preparing, maintaining, starting and stopping the machine. Learn more about all the controls and proper use of the machine. WARNING! When using this type of tool, basic precautions should always be followed to reduce the risk of fire, electric shock and injury. - Page 4 the noise of the machine. Keep people and animals away from the work area. Children and people who do not know how to use this tool should not touch it and handle it. Use the product only under daylight or under good artificial light. ...
- Page 5 Do not use the product on a slippery surface. Do not use the product on steep, slippery slopes. If the machine has struck foreign objects, check if the tool is damaged and bring it to repair if necessary. ...
- Page 6 1.5 SYMBOLS Warning symbol. Read the instruction manual. Wear protective equipment: protective helmet, safety glasses, noise protection helmet. Wear protective gloves. Wear protective foot wear. CAUTION : Hot surface. Don't smoke. Guaranteed sound power level.
-
Page 7: Your Product
7. Handle 3. Trigger 8. Motor 4. Safety button 9. Recoil 5. Grab handle 10. Fuel tank 2.2 TECHNICAL DATA Model HTT50-A Maximum engine power 52cm³ 1.45kW 7500/min Maximum speed of the motor 8500/min Engaging speed 3800/min Idle speed 3000/min Fuel tank volume 1.2l... -
Page 8: Filling Fuel Tank
3. FILLING FUEL TANK WARNING: When filling the tank: - The drill should always be stopped and cooled. - Never smoke during refueling. It must not have flames or sparks near the fuel. - Do not attempt to refuel when the engine is hot. - If fuel has been spilled, immediately stop refueling and do not start the engine. -
Page 9: Use
4. USE 4.1 DRILL ROD ASSEMBLY - Place the machine body on a flat and stable location. - Remove the clip and pin on the drill rod. - Install the rod and align the holes to be able to connect the two sets. - Put the pin back in place by clipping. - Page 10 - Hold the drill by grasping the holding handle and main handle - Gradually increase the speed by pressing and holding the safety switch and then pulling the acceleration trigger. Exert some downward force. - When the drill rod has penetrated 10cm into the ground, grasp the frame strongly and increase the effort downwards.
-
Page 11: Maintenance And Storage
4.5 JAMMING AND BREAKDOWNS - When the drill gets stuck, release the accelerator to slow down the machine. you have to release the accelerator and turn it back to idle to loosen it. - In case of failure, stop the machine completely. Check the machine and have it inspected and repaired by a qualified service technician. -
Page 12: Declaration Of Conformity
6. DECLARATION OF CONFORMITY BUILDER SAS ZI, 32 rue Aristide Bergès – 31270 Cugnaux - France Declares that the machinery designated below: PETROL EARTH AUGER Ref：HTT50-A1 Serial number: 20220674774-20220675073 Complies with the provisions of the Directive “ machinery ” 2006/42/EC and national laws transposing it: Also complies with the provisions of the following European directives: EMC Directive 2014/30/EU... -
Page 13: Warranty
7. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 14: Product Failure
8. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 15: Warranty Exclusions
9. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...