Table of Contents
Advertisement
Available languages
Available languages
en
ENGLISH
- Remove adjusting nut (2) with an open-ended
spanner.
Caution! Left-hand thread on left machine
side, i.e. to release the adjusting nut (2) on the left
machine side, turn clockwise!
- Remove clamping flange (3) and sanding disc (4).
- Secure new sanding disc (4) in the reverse order.
- Remount the safety cover (1). Tighten the screws.
- Adjust the spark deflector (13) and workpiece
support (10) as described in chapter 6.2 and 6.1.
a
8. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For the dealer to select the correct accessory, they
need to know the exact model designation of your
power tool.
Wire brushes permitted only for DS 150 Plus,
DS 200 Plus. Max. permissible width: 28 mm.
Wire brushes may only be mounted on the left side.
The assembly is basically the same as for sanding
discs (see chapter 8.1), however, the suitable
reducing sleeve supplied must be inserted.
A Wire brushes....................... Order no:
D= 150 mm: ..................... 629070000
D= 200 mm: ..................... 629072000
B Sanding discs .................... Order no:.
D= 125 mm:
36 P: ....................... 629088000
60 N: ....................... 629089000
D= 150 mm:
36 P: ....................... 630632000
60 N: ....................... 630633000
D= 200 mm:
36 P: ....................... 630784000
60 N: ....................... 630785000
C Stand
Order no.:........................ 623875000
D Wall bracket
Order no.: ........................ 623865000
For the complete range of accessories, see
www.metabo.com or the main catalogue.
9. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from Metabo
available from the Metabo service.
8
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
10. Environmental Protection
Metabo's packaging can be 100% recycled.
Worn out power tools and accessories contain
considerable amounts of valuable raw and rubber
materials, which can be recycled.
These instructions are printed on chlorine-free
bleached paper.
11. Technical Specifications
Explanatory notes regarding the specifications on
page 3.
Subject to change in accordance with technical
progress.
D
= minimal diameter of the sanding disc
min
D
= maximum diameter of the grinding wheel
max
d
= Hole diameter of the grinding wheel
B
= maximum thickness of the sanding disc
max
n
= no load speed
0
v
= Belt speed in idle mode
0
I
= Current at 120 V
120 V
P
= Rated input power (S1)
1
P
= Rated input power (S2 30min)
2
P
= Power output (S2 30min)
3
M
= Breakdown torque
K
m
= weight
Typical A-effective perceived sound levels:
L
= sound-pressure level
pA
L
= acoustic power level
WA
K
= Uncertainty (sound level)
...
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
The device was tested with S2 (30 min).
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Advertisement
Table of Contents
