Table of Contents
Advertisement
right way, then push the rear wheels on and make
sure that they click into place (fig_b). To mount the
front wheels, fit them into the uprights until they lock
into place (fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle tube
faces upwards, align it with the stroller (Fig_a).
Fasten the handle to the frame as shown in the figure
(Fig_b).
To complete the operation, press the two side buttons
on the handle (Fig_c) to ensure the handle pushes in
all the way, until it clicks into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the basket tube
to the horizontal position. Press the silver buttons
under the metal basket tube located at the back of
the stroller (fig_a) and remove the metal tube (fig_b).
Thread the tube through the fabric loop on the back
of the basket, making sure that the two silver buttons
are facing downward (fig_c). Re-attach the tube to the
housings (fig_d).
5 Secure the two upper basket vinyl eyelets to the two
grey buttons on either side of the metal tube housing.
Please note that the eyelets open (fig_e). Remove the
cardboard from the lower rear bar.
WARNING: Secure the two lower basket vinyl eyelets
to the two grey buttons on the top of the lower rear
bar. Please note that the eyelets open (fig_f).
WARNING If this operation is not performed correctly,
the basket will not properly hold the weight.
Attach the basket tabs to the grey buttons on the
front of the frame (figure).
6 FIXED OR SWIVELING FRONT WHEELS: Lift the levers
to prevent the wheels from swiveling (fig_a) and
lower them to allow the wheels to swivel (fig_b). On
uneven surfaces, the wheels should be set to their
fixed position.
7 BRAKE: Press the lever down to apply the brake on the
chassis and lift it to release the brake.
8 ADJUSTABLE HANDLEBAR: To adjust the height of the
handlebar, press both of the side buttons at the same
time (fig_a) and swing it into the desired position
(fig_b), then release the buttons.
9 FOLDING UP: The chassis can be folded up without
the seat, with the seat facing the person pushing
(recline the backrest before folding it) or with the
seat facing forward. To fold the stroller, it is best to
set the front wheels to their fixed position and close
the hood (if fitted). Place the handle as shown in the
figure (fig_a).
Pull the inside handle on the base (fig_b) and lift it
(fig_c); th e handle will drop forward until the frame
is closed.
10 To ensure the frame is closed properly, check that
the side fastener is enabled (fig_a). When closed, the
frame remains in the upright position (fig_b).
11 For greater compactness, it is possible to remove the
wheels.
To remove the rear wheels: pull outwards on the lever
located under the rear bar and remove the wheels as
shown in figure (fig_a).
To remove the front wheels: press the tab as shown,
and remove the wheel (fig_b).
TRANSPORT: the stroller can be carried comfortably
locking the front wheels and grasping the main handle
(fig_c).
GANCIOMATIC SYSTEM
12
Ganciomatic is a fast and practical system that allows
you to attach the pram body, the car seat and the seat
to the Ganciomatic base of the chassis in one quick
step.
SERIAL NUMBERS
13 Information about the production date can be found
on the Futura/Book Smart Chassis.
_ The product name, production date and serial number
of the chassis.
This information is required for any complaints.
INSTRUCTIONS
Futura/Book Smart SEAT
PRODUCT CHARACTERISTICS
_ The item is numbered progressively.
_ The Futura/Book Smart Seat is a reversible seat: it can
turn to face mum or to face outwards.
The images referring to the textile details may
differ from the collection purchased.
1 FRONT BAR: To attach the front bar, slide the
attachments into the armrests and push towards
the seat until they lock into place (fig_a). To remove
the front bar, press the two buttons (fig_b) and pull
out (fig_c). Open the front bar on one side only, to
facilitate the child's entry and exit.
2 BACKREST: to adjust the backrest, lift the handle
(fig_a) and recline it to the desired position (fig_b).
The backrest can be adjusted into different positions.
3 FOOTREST: before adjusting the foot rest, ensure its
cover is accurately fitted; if it isn't, fit it accordingly. To
lower the footrest push the two levers downwards and
then push the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
4 FIVE POINT SAFETY HARNESS: To fasten it, push the
two waist strap buckles (with the shoulder straps
attached – arrow_a) into the leg divider until they click
into place (arrow_b). To unfasten it, press the round
button in the centre of the buckle (arrow_c) and pull
the waist straps out (arrow_d).
5 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it, move it
in the opposite direction.
6 To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow_a) until the
buckles are released and insert them in the backrest
loops (arrow_b). Remove the shoulder straps from the
sack (arrow_c) and insert them in the most appropriate
loop (arrow_d), then re-attach the two buckles on the
rear of the backrest (arrow_e) The buckles are securely
attached when a click is heard (fig_f).
7 HOOD: slide the hood's attachments into the seat's
attachments (fig_a) and fasten the sides with the
elastics (fig_b). To remove the hood: pull out the
attachments and unfasten.
8 The hood has a double zip and can be extended
(fig_a) Open and pull the hood to extend it (fig_b).
9 It has an insert in the front part for more shade (fig_c)
and a slot from which you can hang your child's
favourite toy (fig_d).
10 FOOT MUFF: Lift the leg rest, slide on the foot muff and
button it below (fig_a); then, slide the foot muff under
the front bar (fig_b).
Fasten the foot muff on the sides of the footrest
(fig_c) and inside the seat (fig_d).
11 FASTENING THE SEAT TO THE CARRIAGE: Futura/
Book Smart Seat can be secured to the carriage
either facing mom or the street. Place it centrally on
the carriage alongside the symbols (fig_a) and press
downwards with both hands until it clicks into place
(fig_b). To ensure it is properly secured, grab the seat
from the front bar and pull upwards.
12 RELEASING THE SEAT FROM THE CARRIAGE: Press
the two buttons on the armrests of the seat (fig_a)
and then the two levers underneath (fig_b); pull up
the seat (fig_c) until it releases. If the backrest is fully
reclined forward (in the closed position, facing the
7 -
Advertisement
Table of Contents
