Table of Contents
Advertisement
Quick Links
36-5000 T2 Series Quick Assembly Guide
PACKAGE CONTENTS 36-5000 T2 AND 36-5100 T2
PC1
PC2
PC4
Saw Body
PC1
Left Leg
PC2
Right Leg
PC3
Rip Fence
PC4
Blade Guard
PC5
Miter Gauge
PC6
Push Stick
PC7
Throat Plate
PC8
PC3
Blade Wrench
PC9
36-5000 T2 - Steel Extension Wings (3)
PC10
36-5100 T2 - Cast Iron Extension Wings (2),
Steel Extension Wings (1)
Anti-Kickback Pawls
PC11
Adjustable Feet (2)
PC12
Fixed Wheels (2)
PC13
Hand Wheel Handles (2)
PC14
Rip Fence Handle
PC15
PC11
PC5
PC12
PC6
PC13
PC7
PC14
PC15
PC8
PC9
PC16
PC10
1
PC17
PC18
PC19
10 inch Blade
PC16
(Pre-Installed)
Rear Fence Rail
PC17
Front Fence Rail
PC18
Fence Guide
PC19
Advertisement
Table of Contents
Related Manuals for Delta 36-5000 T2 Series
Summary of Contents for Delta 36-5000 T2 Series
- Page 1 36-5000 T2 Series Quick Assembly Guide PACKAGE CONTENTS 36-5000 T2 AND 36-5100 T2 PC11 PC12 PC13 PC14 PC15 PC17 PC18 PC16 PC19 PC10 10 inch Blade PC16 Saw Body Blade Wrench (Pre-Installed) Left Leg 36-5000 T2 - Steel Extension Wings (3)
- Page 2 HARDWARE PACKAGE 36-5000 T2 AND 36-5100 T2 Hardware Bag “B” Hardware Bag “A” Hardware Bag “D” 006134 007188 007187 003578 005733 HP15 005733 003059 006111 Hardware Bag “C” 006122 007187 HP14 005679 Hardware Bag “E ” 006054 006111 006110 HP14 HP18 HP19 007191...
- Page 3 PACKAGE CONTENTS 36-5052 T2 AND 36-5152 T2 PC11 PC12 PC13 PC14 PC15 PC17 PC18 PC19 PC16 PC21 PC22 PC20 PC10 PC16 10 inch Blade (Pre-Installed) Saw Body Blade Wrench Rear Fence Rail Left Leg 36-5052 T2 - Steel Extension Wings (2) PC10 PC17 36-5152 T2 - Cast Iron Extension Wings (2)
- Page 4 HARDWARE PACKAGE 36-5052 T2 AND 36-5152 T2 Hardware Bag “C” Hardware Bag “A” Hardware Bag “B” 007187 006134 007191 003578 HP24 005733 005733 003059 Hardware Bag “E ” 006265 006263 006264 006122 HP11 HP10 Hardware Bag “D” 005679 007188 007187 003059 007187 HP15...
-
Page 5: Fixed Wheels And Stationary Feet
TOOLS REQUIRED FOR ASSEMBLY (not included) • Flat head screwdriver • 3/8 inch wrench • Phillips head screwdriver • 7/16 inch wrench • 8mm wrench • Framing (Carpenter’s) Square • 10mm wrench • Combination Square • 12mm wrench • Straight Edge •... -
Page 6: Front And Rear Rails
Step 3: FRONT AND REAR RAILS Hardware Bag “C, D” HP14 Using the supplied 3/16 inch T-Handle Allen Wrench, attach the Front Rail [1] to the table front with two 5/16-18 x PC18 1 1/8 inch Flat Countersunk Hex Screw and two 5/16- HP15 Front Rail... -
Page 7: Extension Wings
Step 4: EXTENSION WINGS For Models with Three Extension Wings PC10 PC10 Hardware Bag “C, D, G” Attach the left extension wing [3] to the front rail PC10 using two 5/16-18 x 1-1/8 inch Flat Countersunk Hex LEFT EXTENSION LEFT EXTENSION WING WING Screws... -
Page 8: Wood Extension Table
Step 5: EXTENSION WINGS For the 36-5052 T2 and 36-5152 T2 PC10 Hardware Bag “D” PC10 Attach both extension wings [3] to the front rail using PC10 RULER four 5/16-18 x 1-1/8 inch Flat Countersunk Hex Screws RIGHT EXTENSION RIGHT EXTENSION and 5/16-18 Hex Flange Nuts HP15 HP14... -
Page 9: Fence Guide And Power Control Box
Loosely assemble three 5/16-18 x 7/8 inch Hex Head Screws with Split Lock Washers , 8 x 16 x 1t Flat Washers and three 5/16-18 Hex Flange Nuts into HP16 HP14 the three holes into the side of the extension wing as shown. -
Page 10: Installing The Handles
Step 8: INSTALLING THE HANDLES Elevation and Bevel Hand Wheels The elevation and Bevel Handles are packaged together in the box, please install as follows: Insert one Handle to the Elevation Hand Wheel located PC14 in the front of the Saw, as seen in Figure 17. Insert one Handle to the Bevel Hand Wheel located on PC14... -
Page 11: Step 12: Anti-Kickback Pawls
Step 12: ANTI-KICKBACK PAWLS To reduce the risk of serious personal injury, Anti-Kickback Pawls MUST be in place when making a through cut See Figure 22 and locate the Anti-Kickback Pawls Mounting Slot in the middle of the top edge of the Riving Knife. Slide Slot in the middle of the Anti-Kickback Pawls Assembly along the top of the Riving Knife until the...