Kohler K-20629T-BW Installation Instructions Manual page 21

1. Method one: Press from top (Mask is reserved
access panel)
1. 安装方式一：顶按（方外罩为预留检修口）
Cut apart the cable tie of the air hose. Pull it out and put into
the tank.
Remove the top cover, install the mask in the block screen of
the tank, and tighten the screw to fixate the mask to the tank.
Note: Do not remove and discard the mask cover before
installation of the water tank faceplate.
Foreign matters and dusts should be prevented from
entering the water tank during construction.
将导气软管的扎线带剪开，导气软管抽出放入水箱。
将顶部遮板取下，将方外罩装在水箱上原遮板的位置，并拧
紧螺丝使方外罩紧固在水箱上。
注： 方外罩遮板，安装水箱面板前请勿移除和废弃。
避免施工过程中异物及灰尘进入水箱。
2. Methods two and three: Remote installation
(Reserve access panel at front cover or top cover)
2. 安装方式二和三：远程安装（需在水箱正面遮板或者顶部
遮板位置处预留相应大小的检修口）
A. Remote hose installation
A. 远程气管安装
Put remote hose through the tube (Customer prepare),
reach to the faceplate location.
将外置远程气管穿过穿线管（客户准备），引到面板的安
装位置。
B. Gap for remote installation
B. 远程安装避位
Method two: Remote pinch installation
安装方式二：远程扣板安装
Reserve 80±3mm gap on the wall. 7~20mm thickness is
recommended to fixate pinch. Recommended installation
hole size of L X W mm and the depth reserved of pinch
15~25mm on the back of finished wall to fixate pinch are
as follows:
墙面预留 80±3mm 深的避位，扣板安装厚度建议
7~20mm，扣板安装的建议安装孔 L X W (mm)，完工墙
内侧预留扣板安装深度 15~25mm，见如下两种尺寸及适
配面板型号：
+2
LXW: 201 X 136
0
K-20341T-PNE
K-75890T-PNE
+2
LXW: 146 X 41
0
K-23055T-PNE
Method Three: Remote installation of mask
Leave a gap of at least 88mm.
安装方式三：远程方外罩安装
墙面至少预留 88mm 深的避位
1402749-K2-A
+2
mm:
0
K-24149T K-75891T-PNE
K-24151T
+2
mm:
0
Cover
遮板
Screw
螺丝
It is suggested that the thickness of fake
wall rough + decorative surface 80 ± 3mm
建议假墙毛坯+装饰面的厚度 80 ± 3mm
Pinch
扣板
Air Hose
导气软管
Fake Wall Rough
假墙毛坯面
-14-
Mask
方外罩
穿线管 （客户准备）
Recommended
thickness of
decorative board
7~20mm
建议装饰板厚度
7~20mm
It is recommended to
reserve the installation
height of the pinch
15~25mm
建议预留扣板安装高度
W
15~25mm
Faceplate
面板
Locking Plate
定位板
Finished Decorative
Surface
完工装饰面
L
W
Fixate Mask Onto Wall
方外罩固定墙面
At Least 88mm
Gap Reserved
建议预留至少
的避位
88mm
Top Cover
顶部遮板
Finished
Wall
完工墙面