Table of Contents
Advertisement
2
Making/Answering Calls
Back side
Ringer
Indicator
Talk/Ringer Indicator
[
]
[SP-PHONE]
Microphone
2-A Making Calls
1
Press [
] then dial a phone number.
OR
To have a hands-free phone conversation, press
[SP-PHONE] and dial a phone number. When the other
party answers, talk into the microphone.
≥The Talk/Ringer indicator lights.
≥If an alarm tone sounds, see section 4-H.
2
To hang up, press [OFF] or place the handset on the
base unit.
≥The indicator light goes out.
≥For the best operating performance, see section 4-F.
To redial the last number dialed
Press [
] or [SP-PHONE], then press [REDIAL].
To adjust the receiver/speaker volume while
talking
3 levels (HIGH, MEDIUM and LOW) are available for the receiver
and 6 levels for the speaker.
To increase volume, press [
≥If you try to increase/decrease volume when it is at the
maximum/minimum level, 3 beeps will sound.
If noise interferes with the conversation
Have the unit select a clearer channel by doing one of the
following:
Press [
] (Channel) if talking using [
press [SP-PHONE] (Channel) if talking using [SP-PHONE].
OR
Walk closer to the base unit.
L
M
[
], [
]
[OFF]
[REDIAL]
[VOICE ENHANCER]
and Indicator
L
]. To decrease volume, press [
], or
For assistance, please call: 1-800-211-PANA(7262)
Voice Enhancer Technology
Voice Enhancer Technology helps clarify and improve sound
reception creating a natural-sounding voice that is easy to hear
and understand.
This is accomplished by enhancing the frequency that is
narrowed through the telephone line and comes pre-set to ON at
the factory.
≥When the mode is set to ON, the VOICE ENHANCER indicator
lights in talk or speakerphone mode.
Helpful hint:
Depending on the condition and quality of your telephone line,
Voice Enhancer may emphasize the noise already on the line.
If it becomes difficult to hear the caller, please set Voice Enhancer
mode to OFF. Each time you press [VOICE ENHANCER] while
talking, the mode will change to ON or OFF.
2-B Answering Calls
When a call is received, the unit rings and the Talk/Ringer and
Ringer indicators on the handset and the IN USE indicator on the
base unit flash rapidly.
If the handset is off the base unit, press [
[SP-PHONE].
≥You can also answer a call by pressing any button except [
and [OFF].
OR
If the handset is on the base unit, just lift up.
Selecting the ringer volume
Make sure the unit is not being used and the handset is lifted off
the base unit.
≥To select HIGH (preset), MEDIUM or LOW,
M
≥press [
] or [
M
[
] within 10 seconds to select the volume. The volume will
change and ring.
≥To turn the ringer OFF, press and hold [
sound.
≥To turn the ringer ON, press [
The ringer will sound at the LOW level.
≥You can select the ringer volume while an external call is being
M
received. Press [
].
To set to OFF, press and hold [
Selecting the ringer tone
Make sure the unit is not being used and the handset is lifted off
the base unit. 6 ringer tones are available.
M
L
Press [
] or [
Lighted handset keypad
The handset dialing buttons will light when you press a button or
lift the handset off the base unit. The light will go out after a
few seconds.
L
] to check the current volume, then press [
M
L
] or [
].
M
L
] or [
] while the unit is just ringing.
M
] until 2 beeps sound.
], then press [1] (preset) to [6] within 10 seconds.
Section 2
] or
M
L
], [
]
L
] or
M
] until 2 beeps
- Quick Links:
- Special Features
Hide quick links:
Advertisement
Table of Contents
